My E1 has 10 lines from my telco, 10 lines are blocked and 20 are idle.
I guess those 10 blocked are my lines(channels). Also reading this:
http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2
i come to this lines:
"...
cas=110-124:1101
The 4 characters after the colon in the cas statements define the idle
patternfor the signalling bits. For China and Thailand you should use
1111 instead of 1101. 1101 should be correct for all other countries
using MFC/R2. This pattern puts the trunk in the blocked state, so when
no application software is using the trunk it behaves in a sensible way.
(...)
You should get a green light. If you make calls into the E1 you
find the E1 is blocked. This is the correct state before asterisk is
started."
I use 1101, that should be correct, and it should be correct to have 10
lines blocked, 1 to 10. It is also correct that those 10 lines are
blocked _before_ asterisk is started. But the problem is that asterisk
says those lines are still blocked when i try to simulate a call.
Using libunicall-0.0.2's testcall executable i get this output, and as
you can see initialli y have 10 blocked lines :-(, errors from line 11
to 31 (i only have 10 lines) and then messages of "local end unblocked!"
for each of the 31 lines.
./testcall
2005/08/06 07:45:02 MFC/R2 Chan 1: call control(8)
2005/08/06 07:45:02 MFC/R2 Chan 1: unblock
2005/08/06 07:45:02 MFC/R2 Chan 1: 1001 -> [1/40000000/Idle
/Idle ]
2005/08/06 07:45:02 MFC/R2 Chan 2: call control(8)
2005/08/06 07:45:02 MFC/R2 Chan 2: unblock
2005/08/06 07:45:02 MFC/R2 Chan 2: 1001 -> [1/40000000/Idle
/Idle ]
(...snip...)
2005/08/06 07:45:02 MFC/R2 Chan 30: call control(8)
2005/08/06 07:45:02 MFC/R2 Chan 30: unblock
2005/08/06 07:45:02 MFC/R2 Chan 30: 1001 -> [1/40000000/Idle
/Idle ]
2005/08/06 07:45:02 MFC/R2 Chan 31: call control(8)
2005/08/06 07:45:02 MFC/R2 Chan 31: unblock
2005/08/06 07:45:02 MFC/R2 Chan 31: 1001 -> [1/40000000/Idle
/Idle ]
Chan 1: -- Far end blocked! :-(
Chan 2: -- Far end blocked! :-(
Chan 3: -- Far end blocked! :-(
Chan 4: -- Far end blocked! :-(
Chan 5: -- Far end blocked! :-(
Chan 6: -- Far end blocked! :-(
Chan 7: -- Far end blocked! :-(
Chan 8: -- Far end blocked! :-(
Chan 9: -- Far end blocked! :-(
Chan 10: -- Far end blocked! :-(
Chan 11: -- Protocol failure on channel 0, cause (32773) Unexpected CAS
bit pattern
Chan 12: -- Protocol failure on channel 0, cause (32773) Unexpected CAS
bit pattern
(...snip...)
Chan 31: -- Protocol failure on channel 0, cause (32773) Unexpected CAS
bit pattern
2005/08/06 07:45:02 MFC/R2 Chan 1: local_unblocking_expired
Chan 1: -- Local end unblocked! :-)
2005/08/06 07:45:02 MFC/R2 Chan 2: local_unblocking_expired
Chan 2: -- Local end unblocked! :-)
2005/08/06 07:45:02 MFC/R2 Chan 3: local_unblocking_expired
Chan 3: -- Local end unblocked! :-)
(...snip...)
2005/08/06 07:45:02 MFC/R2 Chan 30: local_unblocking_expired
Chan 30: -- Local end unblocked! :-)
2005/08/06 07:45:02 MFC/R2 Chan 31: local_unblocking_expired
Chan 31: -- Local end unblocked! :-)
Athiel E. Criollo Merino wrote:
Seems like your carrier is assigning you channels from 11 and up to
make calls, why dont test making a definition for group 1 from lines
11 to 20...
Regards
In spanish.
Ariel, parece que Telmex te está asignando los timeslots 11 al 20 para
tus lineas.
por que no pruebas con tu grupo 1, asignandole solamente desde la
linea o timeslot 11 hasta el 20.
No se mucho sobre señalizacion, pero tiene algo de logica lo que te
estoy diciendo.
Suerte.
Athiel Criollo
2005/8/3, Ariel Molina R. <[EMAIL PROTECTED]>:
I've been trying to configure an E1 in Mexico using unicall, i went
into vozdigital, googled this list, and finally followed this
instructions:
http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2
I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10
"channels" assigned from my telco.
However when i try to simulate a call using this call file:
--------call file------
Channel: UniCall/g1/1
Callerid: <4772140099>
MaxRetries: 0
RetryTime: 600
WaitTime: 600
Context: principal_in
Extension: 014433988789
Priority: 1
----------------------
I get this messages
--------------------------------------
Aug 4 11:46:06 WARNING[9420]: chan_unicall.c:1240 unicall_call:
Make Call failed - Blocked
Aug 4 11:46:06 NOTICE[9420]: channel.c:1827 __ast_request_and_dial:
Unable to request channel UniCall/g1/1
-- Hungup 'UniCall/11-1'
Aug 4 11:46:06 NOTICE[9420]: pbx_spool.c:229 attempt_thread:
Call failed to go through, reason 0
--------------------------------------
So i can see Unicall channels are configured but blocked (as UC show
channel). There is not much info about unicall so i require your
advice, what can i do? Where do i look?
Also i constantly receive messages
Aug 4 11:54:07 WARNING[9402]: chan_unicall.c:2865 handle_uc_event:
Unicall/14 event Protocol failure
for each one of the 30 (31?) channels.
I send you my configs and important command outputs:
My zaptel.conf
-------------------
# MFC/R2 does not normally use CRC4
span=1,1,0,cas,hdb3
cas=1-15:1101
cas=17-31:1101
loadzone=mx
defaultzone=us
-------------------
My unicall.conf
-------------------
[channels]
context=incoming
usecallerid=yes
hidecallerid=no
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
musiconhold=default
protocolclass=mfcr2
protocolvariant=mx,10,10
protocolend=cpe
group = 1
channel => 1-15
channel => 17-31
-------------------
"ztcfg -vv" outputs
-------------------
SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: CAS / User (Default) (Slaves: 01)
Channel 02: CAS / User (Default) (Slaves: 02)
(...)
Channel 30: CAS / User (Default) (Slaves: 30)
Channel 31: CAS / User (Default) (Slaves: 31)
30 channels configured.
-------------------
"UC show channels" says
-------------------
Channel Extension Context Status Language MusicOnHold
1 incoming Blocked default
2 incoming Blocked default
3 incoming Blocked default
4 incoming Blocked default
5 incoming Blocked default
6 incoming Blocked default
7 incoming Blocked default
8 incoming Blocked default
9 incoming Blocked default
10 incoming Blocked default
11 incoming Idle default
12 incoming Idle default
(...)
31 incoming Idle default
---
@-@
_______________________________________________
Asterisk-Users mailing list
[email protected]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
Asterisk-Users mailing list
[email protected]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
