Did you find a solution to this?
Kib Eki wrote:
yes, fedora 3 but without any changes at the sources
Master Abi wrote:
Are you using Redhat/Fedora? If I remember those init scripts is for
Redhat/Fedora. I am using gentoo.
Did you make any modifications to wct4xxp.c. or pass any parameters to
zaptel. I see there is a #define SUPPORT_GEN1 in to wct4xxp.c which I
commented out, but it made no difference. ztcfg seems to where the
channels become unassigned.
Thanks again.
Kib Eki wrote:
Hi,
we also got one V2 TE405P card. It works fine now. At the moment we
use for bridging the Pri to our old PBX.
You must use zaptel, libri and asterisk v 1.0.8 or higher. We use
1.0.9 at the moment.
zaptel:
after make; make install i also executed make config. This copies the
correct startup script to /etc/init.d/zaptel. Without this it also
didn't worked for me.
Master Abi wrote:
Hi
I got the 2nd Gen firmware upgraded on the TE405P. I recompiled
after putting in the upgraded board but did not change any conf, but
the spans become active but will not come up.
I guess I am missing something or are the any changes to the
zaptel/libpri software that is required. I cannot find any info
about this or does this new firmware only work with latest CVS. I am
using 1.0.9 with 2.6.12 kernel
Zapata Telephony Interface Registered on major 196
Found TE4XXP at base address fdfff000, remapped to f8928000
TE4XXP version c01a0164, burst ON, slip debug: OFF
TE4XXP running with work queues.
FALC version: 00000005, Board ID: 00
Reg 0: 0x364e9400
Reg 1: 0x364e9000
Reg 2: 0xffffffff
Reg 3: 0x00000000
Reg 4: 0x00000001
Reg 5: 0x00000000
Reg 6: 0xc01a0164
Reg 7: 0x00001f00
Reg 8: 0x00000000
Reg 9: 0x00ff0000
Reg 10: 0x00000000
TE4XXP: Launching card: 0
TE4XXP: Setting up global serial parameters
Found a Wildcard: Wildcard TE405P (2nd Gen)
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
About to enter spanconfig!
Done with spanconfig!
About to enter spanconfig!
Done with spanconfig!
Unassigning channel 0/1!
Unassigning channel 0/2!
Unassigning channel 0/3!
Unassigning channel 0/4!
Unassigning channel 0/5!
Unassigning channel 0/6!
Unassigning channel 0/7!
Unassigning channel 0/8!
Unassigning channel 0/9!
Unassigning channel 0/10!
Unassigning channel 0/11!
Unassigning channel 0/12!
Unassigning channel 0/13!
Unassigning channel 0/14!
Unassigning channel 0/15!
Unassigning channel 0/16!
Unassigning channel 0/17!
Unassigning channel 0/18!
etc...
This was working for 10 months before the upgrade.
Master
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation sponsored by Easynews.com --
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
