... which is equivalent to my protocol=0x22 ;)
Nevertheless. I think it was a problem with chan_capi being too old
and not supporting protocol=0x22 layermask=0xf (it would not work
without layermask=0xf).
I am currently trying to get it working with chan_misdn. Will let you
know how it goes. It was a pain in the arse to find some document
about how to get it running, so I hope other people may use my
findings somehow.
L. Riem
[EMAIL PROTECTED]
Le 10 oct. 05 à 16:34, Craig Guy a écrit :
Hi,
Yes, you can use the Fritz! in PTP mode, though only if you are
using the mISDN drivers. The mISDN driver should be called like this:
modprobe avmfritz protocol=34
Craig
----- Original Message ----- From: "Lionel Riem" <[EMAIL PROTECTED]>
To: <asterisk-users@lists.digium.com>
Sent: Monday, October 10, 2005 4:04 PM
Subject: [Asterisk-Users] AVM Fritz! + chan_capi + mISDN + PTP
Hello everyone,
I have been using an AVM Fritz! card with chan_capi and mISDN for
quite a while in PTM mode and it was working finely.
Now, I needed more DID/MSN, so I switched to PTP. But now nothing
works anymore :(
I am using Asterisk on Debian Sarge stable and installed Asterisk
along with chan_capi from apt-get. I installed mISDN from the CVS
of isdn4linux.de.
It is :
- Asterisk 1.0.7 with bristuff
- chan_capi 0.3.5
When I load the whole modules lot, I get the following in dmesg:
Modular ISDN Stack core $Revision: 1.25 $
mISDNd: kernel daemon started
ISAC module $Revision: 1.16 $
mISDNd: test event done
CAPI Subsystem Rev 1.1.2.8
capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
ISDN L1 driver version 1.11
ISDN L2 driver version 1.20
mISDN: DSS1 Rev. 1.30
mISDN Capi 2.0 driver file version 1.14
X25 DTE modul version 1.8
AVM Fritz PCI/PnP driver Rev. 1.30
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 10 (level, low) -> IRQ 10
mISDN_fcpcipnp: found adapter Fritz!Card PCI v2 at 0000:00:14.0
fritz card cd09a000 dch cd09a094 bch1 cd09a214 bch2 cd09a3a0
AVM PCI V2: stat 0x240020e
AVM PCI V2: Class E Rev 2
AVM PnP: HDLC version 2
mISDN: AVM Fritz!PCIv2 config irq:10 base:0xEC00
spin_lock_adr=cd09a024 now(d015b867)
busy_lock_adr=cd09a024 now(d015b867)
AVM PCI/PnP: reset
AVM PCI/PnP: S0/S1 40/2
Fritz1 ISAC STAR 40
Fritz1 ISAC MODE c0
Fritz1 ISAC ADF2 ff
Fritz1 ISAC ISTA 0
Fritz1 ISAC CIR0 7
mISDN_isac_init: ISACSX
Fritz1 HDLC 1 STA 82000000
Fritz1 HDLC 2 STA 82000000
AVM Fritz!PCI: IRQ 10 count 4
fritz 1 cards installed
Here is my /etc/asterisk/capi.conf:
;
; CAPI config
;
;
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
txgain=0.8
[interfaces]
mode=immediate
isdnmode=ptp
msn=*
incomingmsn=*
controller=1
softdtmf=1
context=dispatcher
accountcode=
devices=2
Here is my /etc/modprobe.d/capi conf file:
alias /dev/capi20 avmfritz
alias char-major-68-0 avmfritz
install avmfritz /sbin/modprobe capi; \
/sbin/modprobe mISDN_core; \
/sbin/modprobe mISDN_l1; \
/sbin/modprobe mISDN_l2; \
/sbin/modprobe l3udss1; \
/sbin/modprobe mISDN_capi; \
/sbin/modprobe mISDN_x25dte; \
/sbin/modprobe --ignore-install avmfritz protocol=0x22
remove avmfritz /sbin/modprobe -r --ignore-remove avmfritz; \
/sbin/modprobe -r mISDN_x25dte; \
/sbin/modprobe -r mISDN_capi; \
/sbin/modprobe -r l3udss1; \
/sbin/modprobe -r mISDN_l2; \
/sbin/modprobe -r mISDN_l1; \
/sbin/modprobe -r mISDN_core; \
/sbin/modprobe -r capi
"capiinfo" shows me:
asterisk:/etc/asterisk# capiinfo
Number of Controllers : 1
Controller 1:
Manufacturer: mISDN CAPI controller Fritz1
CAPI Version: 2.0
Manufacturer Version: 1.0
Serial Number: 0002
BChannels: 2
Global Options: 0x00000018
DTMF supported
Supplementary Services supported
B1 protocols support: 0x00000003
64 kbit/s with HDLC framing
64 kbit/s bit-transparent operation
B2 protocols support: 0x00000043
ISO 7776 (X.75 SLP)
Transparent
Transparent (ignoring framing errors of B1 protocol)
B3 protocols support: 0x00000005
Transparent
ISO 8208 (X.25 DTE-DTE)
0100
0200
18000000
03000000
43000000
05000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000
Supplementary services support: 0x00000012
Terminal Portability
Call Forwarding
In Asterisk, when an incoming call arrives, it shows me the
following:
Asterisk Ready.
*CLI> capi info
Contr1: 2 B channels total, 2 B channels free.
*CLI> capi debug
CAPI Debugging Enabled
*CLI>
*CLI>
*CLI> -- INFO_IND ID=001 #0x0001 LEN=0016
Controller/PLCI/NCCI = 0x101
InfoNumber = 0x18
InfoElement = <89>
-- INFO_IND ID=001 #0x0001 LEN=0016
Controller/PLCI/NCCI = 0x101
InfoNumber = 0x18
InfoElement = <89>
Oct 10 09:17:16 NOTICE[5948]: chan_capi.c:1184 find_pipe: PLCI
doesnt match last pipe (PLCI = 0x101)
Oct 10 09:17:16 NOTICE[5948]: chan_capi.c:1301 pipe_msg: INFO_IND
ID=001 #0x0001 LEN=0016
Controller/PLCI/NCCI = 0x101
InfoNumber = 0x18
InfoElement = <89>
-- CONNECT_IND ID=001 #0x0002 LEN=0044
Controller/PLCI/NCCI = 0x101
CIPValue = 0x1
CalledPartyNumber = <81>20
CallingPartyNumber = <01 83>0123456789
CalledPartySubaddress = default
CallingPartySubaddress = default
BC = <80 90 a3>
LLC = default
HLC = default
AdditionalInfo
BChannelinformation = default
Keypadfacility = default
Useruserdata = default
Facilitydataarray = default
Oct 10 09:17:16 NOTICE[5948]: chan_capi.c:1931 capi_handle_msg:
CONNECT_IND ID=001 #0x0002 LEN=0044
Controller/PLCI/NCCI = 0x101
CIPValue = 0x1
CalledPartyNumber = <81>20
CallingPartyNumber = <01 83>0123456789
CalledPartySubaddress = default
CallingPartySubaddress = default
BC = <80 90 a3>
LLC = default
HLC = default
AdditionalInfo
BChannelinformation = default
Keypadfacility = default
Useruserdata = default
Facilitydataarray = default
== CONNECT_IND
(PLCI=0x101,DID=20,CID=0123456789,CIP=0x1,CONTROLLER=0x1)
-- creating pipe for PLCI=0x101 msn = *
And it just hangs here. After a little while (10 seconds or so),
the other party gets a message from the teclo telling him that
"this number cannot receive calls at the moment".
I really hope that someone may be able to help me. I am really
stuck here and I need to be able to receive calls quite quickly
now, as it's my business line.
If you need anything else, just let me know.
Thanks,
L. Riem
[EMAIL PROTECTED]
_______________________________________________
--Bandwidth and Colocation sponsored by Easynews.com --
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation sponsored by Easynews.com --
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation sponsored by Easynews.com --
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
