Might be sharing a brain today... Here is my config as it stands: /etc/zapata.conf span=1,1,1,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone = us
/etc/asterisk/zaptel.conf switchtype = 5ess signalling = pri_net channel => 1-23 On the merlin side, I have: A DS1 SLOT ATTRIBUTES A Slot Type Format Supp Signal LineComp A 5 PRI ESF B8ZS DMI-MOS 2 A BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing: A 80 5 ElecTandNtwk Route Directly to UDP I am trying to finish my install up ... > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:asterisk-users- > [EMAIL PROTECTED] On Behalf Of Sterling Moses > Sent: Friday, November 11, 2005 1:17 PM > To: [email protected] > Subject: [Asterisk-Users] asterisk T100P to Merlin Legend > > I am running into issues with this same setup and would like to > update the wiki with information on connecting an avaya legend to an > asterisk server via a T100P. Please post your experiences with the > legend and asterisk so we can compile a great list of step by step > instructions for the wiki. > > Some questions I have pertain to the protocol used between the MLPBX > and the T100P card. > > We are running ML Release 7.0 with a 100D DS1 Card (hardware 1B, > firmware 90) and a Cross Over Cable (1,2,4,5 -> 4,5,1,2) to the T100P. > > We have selected the Legend-Ntwk type on the ML side. > > Should we be running something like 5ESS rather than legend-ntwk? > > Again, if anyone has semi-detailed to detailed instructions for the > ML Legend or ML Magix please post them so we can update the wiki. > > Sterling. > > > >Spectro, > > > >I have a T100P connected to my Merlin Magix and it works like a > champ. I am > >using an older T1 card (one pulled from a Merlin Legend) without any > >problems. The card is a "100D 1 T1 Trunk" blade. > > > >I have my system configured as a PRI (23B+D). The T100P is > configured to > >signal with pri_net and to provide timing. I used the 5ESS > protocol, but I > >suppose any of the PRI variants supported by both devices would work. > > > >I do not have (or need) any CSU/DSU equipment in between the two > devices. I > >simply built a crossover T1 cable (warning - not the same as an > Ethernet > >cross-over cable) and connected the two devices. The card and the > switch > >synched up and worked immediately. > > > >The hardest part was programming the ARS table to properly make use > of the > >connection. > > > >As for the insertion of the new card -- I had to do a "board > renumber" and > >it did mess with the dial plan on the switch a bit. Stations did not > >change, but the trunk numbering did. (This may be specific to my > >installation -- Magix/Legend are a field unto themselves.) > > > >Good luck with the install. My number is below if you have additional > >questions. > > > >Thanks, > > > >Steve > > > >Steven Sokol > >Owner/Manager > >Sokol & Associates, LLC > > > >Phone: 816.822.1807 > >IaxTel: 700.613.9004 > >Web: http://www.sokol-associates.com > > >ASK ME ABOUT AstriCon 2004! > >http://www.astricon.net/ > > > > > >> -----Original Message----- > >> From: asterisk-users-admin at lists.digium.com [mailto:asterisk- > users- > >> admin at lists.digium.com] On Behalf Of spectro > >> Sent: Sunday, August 22, 2004 11:25 AM > >> To: asterisk-users at lists.digium.com > >> Subject: [Asterisk-Users] asterisk T100P to Merlin Legend > >> > >> Management just approved purchase of a Digium T100P and a T1 card > for > >> our Merlin Legend Switch. I will appreciate comments from anyone > >> performing this installation before: > >> > >> - Which T1 card did you use in the Merlin Legend? > >> - Did you require any special interface? (CSU/DSU, etc) > >> - Any items to watch during installation. > >> > >> Also we will need to remove one of our old analog Trunk cards to > >> accomodate the new T1 interface in the switch. This switch > already has > >> two T1 cards in it. I don't know much about restriction in the > Merlin > >> Legend Switch, but our phone tech told me some horror stories about > >> taking a card out of the switch. I know this is OT and we will > >> probably have our switch part supplier to take care of that but I > will > >> appreciate any comments. > >> > >> Thanks in advance > >> _______________________________________________ > >> Asterisk-Users mailing list > >> Asterisk-Users at lists.digium.com > >> http://lists.digium.com/mailman/listinfo/asterisk-users > >> To UNSUBSCRIBE or update options visit: > >> http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ > --Bandwidth and Colocation sponsored by Easynews.com -- > > Asterisk-Users mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
