What does the TE406 leds indicate? On 11/28/05, William K. Volkman <[EMAIL PROTECTED]> wrote: > I've looked through the archives of the mailing list for the > last year and although informative I've not been successful > at get this to work. We had a working Asterisk PBX system > with 3 Digium X101P FXO lines and two TDM400P FXS cards. > I've setup an ADIT 600 with an 8 port FXO card (and an > 8 port FXS card not currently installed). We are going > to be adding a T1 for incoming calls this week. I removed > two of the X101P cards and installed a TE406P. I'm using > Asterisk 1.0.9 (and matching zaptel, libpri) from tar files. > > /etc/zaptel.conf has this configuration: > span=1,1,0,esf,b8zs,yellow > span=2,0,0,esf,b8zs > span=3,0,0,esf,b8zs > span=4,0,0,esf,b8zs > #Modular unit, first card is FXO > fxsks=1-3 > unused=4-8 > #Modular unit, 1 FXS cards > unused=9-16 > unused=17-24 > unused=25-48,49-72,73-96 > fxsks=97 > fxoks=98-101 > fxoks=102-105 > > /etc/asterisk/zapata.conf has this: > group = 0 > signalling=fxs_ks > context = incoming > busydetect = yes > overlapdial = no > channel => 1-3 > > signalling=fxs_ks > channel => 97 ;X100P > > group = 1 > signalling = fxo_ks > context = internal > ;TDM400P > callerid = "Available" <200> > channel => 98-100 > callerid = "xxxxx" > channel => 101 > ;TDM400P > callerid = "xxxxx" > channel => 102 > callerid = "xxxxx" > channel => 103 > > Parts of my adit configuration: > -Setting slot a. > > set a:1 up > set a:1 fdl none > set a:1 lbo 4 > set a:1 framing esf > set a:1 id "Inbound" > set a:1 linecode b8zs > set a:1 loopdetect csu > set a:1:1-24 side drop > set a:1:1-24 type voice > set a:1:1-24 signal ls > set a:2 up > set a:2 fdl none > set a:2 lbo 1 > set a:2 framing esf > set a:2 id "Outbound PBX" > set a:2 linecode b8zs > set a:2 loopdetect csu > set a:2:1-24 side drop > set a:2:1-24 type voice > set a:2:1-24 signal ls > > -Setting slot 1. > > set 1:1-8 signal lscpd > set 1:1-8 txgain -3 > set 1:1-8 rxgain -6 > > -Setting primary and secondary clock sources. > > set clock1 a:1 > set clock2 internal > > -Setting the system idle pattern for DS0s. > > set idle 0xff > > -Making connections. > > connect a:2:1-3 1:1-3 > > Inbound calls just ring and ring (the leds on the ADIT change > state) however asterisk doesn't respond. Attempts to make > outgoing calls get: > -- Executing Dial("SIP/202-ba07", "Zap/g0/5551212") in new stack > Nov 28 02:54:45 NOTICE[8627]: app_dial.c:764 dial_exec: Unable to create > channel of type 'Zap' > == Everyone is busy/congested at this time > -- Executing Congestion("SIP/202-ba07", "") in new stack > == Spawn extension (from-sip, 95942060, 3) exited non-zero on > 'SIP/202-ba07' > -- Executing Hangup("SIP/202-ba07", "") in new stack > > I've tried just about all combinations of gs/ls/ks for the > signalling to no avail. Here is the output of status: > > > status a:2:1-3 > > DS0 Rx AB Tx AB Signal T1 TP > --- ----- ----- ------ ----------------- -- > a:2:1 01 01 LS Traffic N > a:2:2 01 01 LS Traffic N > a:2:3 01 01 LS Traffic N > > > status 1:1-3 > > FXO Rx AB Tx AB Signal=>T1 Sig T1 TP > --- ----- ----- -------------- ----------------- -- > 1:1 01 01 LSCPD => LS Traffic N > 1:2 01 01 LSCPD => LS Traffic N > 1:3 01 01 LSCPD => LS Traffic N > > > show connect a:2:1-3 > From Desc Desc To > ----------- ------------------ ----------------- --------- > A:02:01 LS VOICE DS0 <--> FXO VOICE LSCPD 1:01 > A:02:02 LS VOICE DS0 <--> FXO VOICE LSCPD 1:02 > A:02:03 LS VOICE DS0 <--> FXO VOICE LSCPD 1:03 > > Can anyone spot what I've got wrong? Any suggestions or hints > welcome. > > Thanks, > William. > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users