Hello,
OK, some things I've found out so far. The ground connection
to the ADIT chassis wasn't really to ground (fixed that, it
made FXS card happy when connected).
Taking a cue from another post I also reduced the number of
options specified in zapata.conf to:
[trunkgroups]
[channels]
context=default
usecallerid=yes
hidecallerid=no
callwaiting=yes
group=1
callgroup=1
pickupgroup=1-2
immediate=no
musiconhold=default
group = 0
signalling=fxs_ks
context = incoming
busydetect = no
overlapdial = no
channel => 25-27
signalling=fxs_ks
channel => 97 ;X100P
group = 1
signalling = fxo_ks
context = internal
channel => 98-100
channel => 101-105
Using zttool I tried to loopback the TE406P span 1 which
switched the ADIT a:2 port into loop back, setting the line
down and back up didn't clear the configuration (I had to
find the "set a:2 line loopdown" command). Moving the link
to span 2 on the TE406P I now can receive incoming calls
(yea!), trying to place an outbound call results in
dead air with the eventual message that the call didn't
go through :-(
Note that both the ADIT and the TE406P were showing
green on the T1 connection however it wasn't until
I changed the connection to span 2 that it started
allowing inbound calls to work, zap show channel 1
showed InAlarm: 1 although I didn't spot any other
error messages.
zztool currently shows:
RED/NOP T4XXP (PCI) Card 0 Span 1
OK T4XXP (PCI) Card 0 Span 2
RED T4XXP (PCI) Card 0 Span 3
RED T4XXP (PCI) Card 0 Span 4
RED Wildcard X101P Board 1
OK Wildcard TDM400P REV E/F Board 1
OK Wildcard TDM400P REV E/F Board 2
The "NOP" on Span 1 appears to mean "Not Opened" however
I don't know what that means.
I've got one more day/night to get this working so any
suggestions are welcome.
Thank you,
William.
On Mon, 2005-11-28 at 03:28, William K. Volkman wrote:
> I've looked through the archives of the mailing list for the
> last year and although informative I've not been successful
> at get this to work. We had a working Asterisk PBX system
> with 3 Digium X101P FXO lines and two TDM400P FXS cards.
> I've setup an ADIT 600 with an 8 port FXO card (and an
> 8 port FXS card not currently installed). We are going
> to be adding a T1 for incoming calls this week. I removed
> two of the X101P cards and installed a TE406P. I'm using
> Asterisk 1.0.9 (and matching zaptel, libpri) from tar files.
>
> /etc/zaptel.conf has this configuration:
> span=1,1,0,esf,b8zs,yellow
> span=2,0,0,esf,b8zs
> span=3,0,0,esf,b8zs
> span=4,0,0,esf,b8zs
> #Modular unit, first card is FXO
> fxsks=1-3
> unused=4-8
> #Modular unit, 1 FXS cards
> unused=9-16
> unused=17-24
> unused=25-48,49-72,73-96
> fxsks=97
> fxoks=98-101
> fxoks=102-105
>
> /etc/asterisk/zapata.conf has this:
> group = 0
> signalling=fxs_ks
> context = incoming
> busydetect = yes
> overlapdial = no
> channel => 1-3
>
> signalling=fxs_ks
> channel => 97 ;X100P
>
> group = 1
> signalling = fxo_ks
> context = internal
> ;TDM400P
> callerid = "Available" <200>
> channel => 98-100
> callerid = "xxxxx"
> channel => 101
> ;TDM400P
> callerid = "xxxxx"
> channel => 102
> callerid = "xxxxx"
> channel => 103
>
> Parts of my adit configuration:
> -Setting slot a.
>
> set a:1 up
> set a:1 fdl none
> set a:1 lbo 4
> set a:1 framing esf
> set a:1 id "Inbound"
> set a:1 linecode b8zs
> set a:1 loopdetect csu
> set a:1:1-24 side drop
> set a:1:1-24 type voice
> set a:1:1-24 signal ls
> set a:2 up
> set a:2 fdl none
> set a:2 lbo 1
> set a:2 framing esf
> set a:2 id "Outbound PBX"
> set a:2 linecode b8zs
> set a:2 loopdetect csu
> set a:2:1-24 side drop
> set a:2:1-24 type voice
> set a:2:1-24 signal ls
>
> -Setting slot 1.
>
> set 1:1-8 signal lscpd
> set 1:1-8 txgain -3
> set 1:1-8 rxgain -6
>
> -Setting primary and secondary clock sources.
>
> set clock1 a:1
> set clock2 internal
>
> -Setting the system idle pattern for DS0s.
>
> set idle 0xff
>
> -Making connections.
>
> connect a:2:1-3 1:1-3
>
> Inbound calls just ring and ring (the leds on the ADIT change
> state) however asterisk doesn't respond. Attempts to make
> outgoing calls get:
> -- Executing Dial("SIP/202-ba07", "Zap/g0/5551212") in new stack
> Nov 28 02:54:45 NOTICE[8627]: app_dial.c:764 dial_exec: Unable to create
> channel of type 'Zap'
> == Everyone is busy/congested at this time
> -- Executing Congestion("SIP/202-ba07", "") in new stack
> == Spawn extension (from-sip, 95942060, 3) exited non-zero on
> 'SIP/202-ba07'
> -- Executing Hangup("SIP/202-ba07", "") in new stack
>
> I've tried just about all combinations of gs/ls/ks for the
> signalling to no avail. Here is the output of status:
>
> > status a:2:1-3
>
> DS0 Rx AB Tx AB Signal T1 TP
> --- ----- ----- ------ ----------------- --
> a:2:1 01 01 LS Traffic N
> a:2:2 01 01 LS Traffic N
> a:2:3 01 01 LS Traffic N
>
> > status 1:1-3
>
> FXO Rx AB Tx AB Signal=>T1 Sig T1 TP
> --- ----- ----- -------------- ----------------- --
> 1:1 01 01 LSCPD => LS Traffic N
> 1:2 01 01 LSCPD => LS Traffic N
> 1:3 01 01 LSCPD => LS Traffic N
>
> > show connect a:2:1-3
> From Desc Desc To
> ----------- ------------------ ----------------- ---------
> A:02:01 LS VOICE DS0 <--> FXO VOICE LSCPD 1:01
> A:02:02 LS VOICE DS0 <--> FXO VOICE LSCPD 1:02
> A:02:03 LS VOICE DS0 <--> FXO VOICE LSCPD 1:03
>
> Can anyone spot what I've got wrong? Any suggestions or hints
> welcome.
>
> Thanks,
> William.
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
