Hi Scott, thanks for your help. The frame errors which you got i don't got. Yes this is a slow machine, but i greenly thought that * can handle about 30 calls on it without problems....
Have you ever run 120 simultaneously calls on one machine ? What does you mean with "How many instances are you running" ? Best regards, Thomas. -----Urspr�ngliche Nachricht----- Von: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Auftrag von Scott Stingel Gesendet: Dienstag, 14. Oktober 2003 02:28 An: [EMAIL PROTECTED] Betreff: RE: [Asterisk-Users] PRI/E1: machine freeze/dies after a few calls Hi Thomas- I didn't look closely at your shell script, but I wrote something similar in Perl (and used shell to start each instance of it). I had a few problems too with a similar setup (although no machine lockups) * You are running quite a slow machine to run this script on many lines at once - I found that I needed a P4, 2.4GHz to keep up with 120 channels simultaneously (I had one system to send and one to receive, and very short calls - 3 seconds). How many instances are you running? Are you doing mySQL call logging? * I found that I could only initiate about 18 calls at exactly the same moment without getting failed outbound call errors from asterisk, so I ended up staggering the start times a little. * With lots of new calls, I had tons of framing errors on the receiving end (and occasional D channel restarts) when routing calls through my DMS100 switch - do you have problems like this? I think this problem is specific to the Nortel switch however. Suggest starting with -vvvvc and routing all output to a log file...?? regards Scott Scott M. Stingel Emerging Voice Technology Inc. Email: [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]> URL: www.evtmedia.com <http://www.evtmedia.com> > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of > Thomas Haeger > Sent: Monday, October 13, 2003 8:00 PM > To: Asterisk User > Subject: [Asterisk-Users] PRI/E1: machine freeze/dies after a > few calls > > > Hi all, > > inside my * is a E400P. The machine is a PII 400Mhz with > 256MB Ram. OS is > Debian woody. * is the newest cvs co. > > I have written a little callgen script which make outgoing > calls through my > *: > > #! /bin/sh > set -e > > n=$1 # Nummer > anz=$2 # Anzhal der Versuche > anz2=$3 # Kan�le > sle=$4 # Timeout bis zum n�chsten Versuch > > if [ -z $4 ]; then > sle=0 > fi > > s=1 > i=1 > while [ $s -le $anz ];do > echo "$s try started..." > while [ $i -le $anz2 ];do > echo -e "Channel: Zap/g1/$n$i\nMaxRetries: 0\nContext: > callgen\nExtension: 1\nPriority: 1\nCallerid:334778\n" > > /var/spool/asterisk/outgoing/call.$i.$s > > sleep 2 > i=$((i + 1)) > done > i=1 > echo "sleep for $sle sec....." > sleep $sle > s=$((s + 1)) > done > > The calls goes out over the first two ports and through a pri > switch (teles) > they come back at the other two ports (3 and 4). > But after a few calls my machine is completly freezed! So > that i have to > restart my machine. > > > Here're my extension.conf, zapata.conf and zaptel.conf: > > > ---->extension.conf: > > [pri1] > exten => _X.,1,SetAccount(pritest) > exten => _X.,2,Answer > exten => _X.,3,Wait(15) > exten => _X.,4,Hangup > > [pri2] > exten => _X.,1,SetAccount(pritest) > exten => _X.,2,Answer > exten => _X.,3,Wait(15) > exten => _X.,4,Hangup > > [pri3] > exten => _X.,1,SetAccount(pritest) > exten => _X.,2,Answer > exten => _X.,3,Wait(60) > exten => _X.,4,Hangup > > > [pri4] > exten => _X.,1,SetAccount(pritest) > exten => _X.,2,Answer > exten => _X.,3,Wait(60) > exten => _X.,4,Hangup > > > [callgen] > exten => 1,1,Wait(90) > > > ---->zapata.conf: > > > ; > ; Zapata telephony interface > ; > ; Configuration file > > [channels] > > pridialplan=local > > switchtype=euroisdn > busydetect=yes > callprogress=no > echocancel=yes > echocancelwhenbridged=yes > ;callwaitingcallerid=no > ;callwaiting=no > > signalling=pri_net > group=1 > context=pri1 > channel => 1-15,17-31 > channel =>32-46,48-62 > > signalling=pri_net > group=3 > context=pri3 > channel => 63-77,79-93 > channel => 94-108,110-124 > > > ---->zaptel.conf > > > span=1,0,0,ccs,hdb3,crc4 > span=2,0,0,ccs,hdb3,crc4 > span=3,0,0,ccs,hdb3,crc4 > span=4,0,0,ccs,hdb3,crc4 > > bchan=1-15,17-31 > dchan=16 > > bchan=32-46,48-62 > dchan=47 > > bchan=63-77,79-93 > dchan=78 > > bchan=94-108,110-124 > dchan=109 > > loadzone = fr > defaultzone=fr > > > > Thanks for your help. > > Regards, > > Thomas. > > > ******************************************* > beroNet technologies GmbH > Dipl.- Ing. Thomas H�ger > Potsdamer Str. 18 A > 14513 Teltow > > FON: +49 (0) 3328 3077731 > FAX: +49 (0) 3328 334779 > Email: [EMAIL PROTECTED] > ******************************************* > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > > _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
