Hi, You could only take timing from one E1 per card. So you should use : span=1,1,0,ccs,hdb3,crc4 span=2,0,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4
instead of : span=1,1,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,1,0,ccs,hdb3,crc4 span=4,1,0,ccs,hdb3,crc4 Le dimanche 25 décembre 2005 à 03:07 -0600, Diyanat Ali a écrit : > Hello! > > I have a TE410P quad span card with 4 E1, i am using asterisk 1.2.1, i was > using it without any issues earlier with just 1 E1 on span 1 and i recently > plugged in 3 more E1's, only span 1 is working, the e1 for span 1 is from a > different provider then the rest, the settings are same for both, but i > constantly get red alaram on the span 2,3,4, i tried all settings, including > the timming source , framing, coding , signalling type etc, without any > sucesss > > what maybe the cause of the red alarm > > Regards > > Diyanat > > lspci -vvv > 06:01.0 Communication controller: Unknown device d161:0410 (rev 02) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ > Stepping- SERR+ FastB2B- > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 > Interrupt: pin A routed to IRQ 74 > Region 0: Memory at fdff0000 (32-bit, non-prefetchable) [size=128] > > lsmod > Module Size Used by Not tainted > wct4xxp 78432 124 > zaptel 183776 250 [wct4xxp] > > > > cat /proc/zaptel/* > Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 > 1 TE4/0/1/1 Clear (In use) .... upto > 16 TE4/0/1/16 HDLCFCS (In use) .... upto > 31 TE4/0/1/31 Clear (In use) > Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS/CRC4 RED > 32 TE4/0/2/1 Clear (In use) .... upto > 47 TE4/0/2/16 HDLCFCS (In use) .... upto > 62 TE4/0/2/31 Clear (In use) > Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" HDB3/CCS/CRC4 RED > 63 TE4/0/3/1 Clear (In use) .... upto > 78 TE4/0/3/16 HDLCFCS (In use) .... upto > 93 TE4/0/3/31 Clear (In use) > Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4" HDB3/CCS/CRC4 RED > 94 TE4/0/4/1 Clear (In use) .... upto > 109 TE4/0/4/16 HDLCFCS (In use) .... upto > 124 TE4/0/4/31 Clear (In use) > > > ztcfg -v > SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) > SPAN 2: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) > SPAN 3: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) > SPAN 4: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) > 124 channels configured. > > zttool > Alarms Span > OK T4XXP (PCI) Card 0 Span 1 > RED T4XXP (PCI) Card 0 Span 2 > RED T4XXP (PCI) Card 0 Span 3 > RED T4XXP (PCI) Card 0 Span 4 > > CLI> zap show status > Description Alarms IRQ bpviol > CRC4 > T4XXP (PCI) Card 0 Span 1 OK 0 0 0 > T4XXP (PCI) Card 0 Span 2 RED 0 0 0 > T4XXP (PCI) Card 0 Span 3 RED 0 0 0 > T4XXP (PCI) Card 0 Span 4 RED 0 0 0 > > > > alpha*CLI> pri show span 1 > Primary D-channel: 16 > Status: Provisioned, Up, Active > Switchtype: EuroISDN > Type: CPE > Window Length: 0/7 > Sentrej: 0 > SolicitFbit: 0 > Retrans: 0 > Busy: 0 > Overlap Dial: 0 > T200 Timer: 1000 > T203 Timer: 10000 > T305 Timer: 30000 > T308 Timer: 4000 > T313 Timer: 4000 > N200 Counter: 3 > > > alpha*CLI> pri show span 2 > Primary D-channel: 47 > Status: Provisioned, In Alarm, Down, Active > Switchtype: EuroISDN > Type: CPE > Window Length: 0/7 > Sentrej: 0 > SolicitFbit: 0 > Retrans: 0 > Busy: 0 > Overlap Dial: 0 > T200 Timer: 1000 > T203 Timer: 10000 > T305 Timer: 30000 > T308 Timer: 4000 > T313 Timer: 4000 > N200 Counter: 3 > its the same as span for the rest as upto span 4 > > > CLI>pri intense debug span 2 > >Unnumbered frame: > >SAPI: 00 C/R: 0 EA: 0 > > TEI: 000 EA: 1 > > M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode > >extended) ] > >0 bytes of data > Sending Set Asynchronous Balanced Mode Extended > > same for the rest > > > zaptel.conf > span=1,1,0,ccs,hdb3,crc4 > bchan = 1-15 > dchan = 16 > bchan = 17-31 > span=2,1,0,ccs,hdb3,crc4 > bchan = 32-46 > dchan = 47 > bchan = 48-62 > span=3,1,0,ccs,hdb3,crc4 > bchan = 63-77 > dchan = 78 > bchan = 79-93 > span=4,1,0,ccs,hdb3,crc4 > bchan = 94-108 > dchan = 109 > bchan = 110-124 > loadzone=se > defaultzone=se > > > > zapata.conf > [channels] > language=us > context=sip > switchtype=euroisdn > pridialplan=unknown > prilocaldialplan=unknown > signalling=pri_cpe > usecallerid=yes > hidecallerid=no > callwaiting=yes > usecallingpres=yes > callwaitingcallerid=yes > threewaycalling=yes > transfer=yes > cancallforward=yes > callreturn=yes > echocancel=yes > echocancelwhenbridged=yes > echotraining=yes > cidsignalling=dtmf > cidstart=ring > rxgain=0.0 > txgain=0.0 > group=1 > callgroup=1 > pickupgroup=1 > immediate=no > callerid=asreceived > > group=1 > channel => 1-15 > channel => 17-31 > > group=2 > channel => 32-46 > channel => 48-62 > > group=3 > channel => 63-77 > channel => 79-93 > > group=4 > channel => 94-108 > channel => 110-124 > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users