On Fri, Dec 30, 2005 at 10:23:26PM +0100, Armin Schindler wrote:
> On Fri, 30 Dec 2005, Louis-David Mitterrand wrote:
> > Hello,
> >
> > I just received a couple SX440isdn phones and was wondering if they can
> > be plugged into a Diva 4BRI port in NT mode and work with
> > asterisk+chan_capi?
>
> Yes, I don't know any reason why it shouldn't work.
>
> > I know they probably work fine with mutliHFC cards with either bristuff
> > of chan_misdn but since I have some spare Divas, I was curious about
> > their potential as phone ports.
> >
> > The Diva's 3 and 4 ports are already set to NT mode at boot time:
> >
> > /sbin/divactrl load -SeparateConfig -c 1 -f ETSI -f1 ETSI -f2 ETSI -u2
> > -x2 -f3 ETSI -u3 -x3
>
> looks good.
>
> > And I think the capi.conf (using Armin's 0.6.1 version) looks OK:
> >
> > [DIVA2]
> > ntmode=yes
> > isdnmode=ptp
> > incomingmsn=*
> > controller=4
> > group=3
> > accountcode=diva
> > context=international
> > echosquelch=0
> > echocancel=no
> > devices=1
>
> isdnmode=ptp is wrong for chan_capi 0.6, use isdnmode=did
>
> > But when I plug the phone into port 3 or 4 no led lights up, even with a
> > Y plug and when dialing I get a busy.
> >
> > Before digging to deep, I am looking for some info on the feasability of
> > that setup.
>
> What type of cable did you use? You need to use a crossed cable with 100 Ohm
> termination.
Hello Armin,
I am now using a cross cable and the green led lights up on the Diva
port when plugging the phone in.
When dialing from the phone I get no debug or trace at the asterisk
console, only a "not possible" message on the phone display and busy
tone. Is there some configuration to do on the phone itself?
When dialing from asterisk I get this:
CAPI Debugging Enabled
-- Executing NoOp("SIP/0146472130-f4c2", "") in new stack
-- Executing Queue("SIP/0146472130-f4c2", "accueil|rnt|||5") in
new stack
> data = DIVA2/2
> parsed dialstring: 'DIVA2' 'NULL' '2' ''
> capi request for interface 'DIVA2'
> parsed dialstring: 'DIVA2' 'NULL' '2' ''
== DIVA2: Call CAPI/DIVA2/2-5 (pres=0x00, ton=0x00)
CONNECT_REQ ID=002 #0x0008 LEN=0054
Controller/PLCI/NCCI = 0x4
CIPValue = 0x1
CalledPartyNumber = <80>2
CallingPartyNumber = <00 80>0146472130
CalledPartySubaddress = default
CallingPartySubaddress = default
BProtocol
B1protocol = 0x1
B2protocol = 0x1
B3protocol = 0x0
B1configuration = default
B2configuration = default
B3configuration = default
GlobalConfiguration = default
BC = default
LLC = default
HLC = default
AdditionalInfo
BChannelinformation = <00 00>
Keypadfacility = default
Useruserdata = default
Facilitydataarray = default
SendingComplete = default
-- Called CAPI/DIVA2/2
-- Called SIP/0146472152
-- Called SIP/0146472131
CONNECT_CONF ID=002 #0x0008 LEN=0014
Controller/PLCI/NCCI = 0x304
Info = 0x0
-- DIVA2: received CONNECT_CONF PLCI = 0x304
> CAPI devicestate requested for DIVA2/2
> CAPI devicestate requested for DIVA2/2
-- SIP/0146472152-487d is ringing
-- Incoming call: Got SIP response 500 "Internal Server Error"
back from 10.0.3.138
-- SIP/0146472131-56e8 is ringing
DISCONNECT_IND ID=002 #0x001f LEN=0014
Controller/PLCI/NCCI = 0x304
Reason = 0x3302
DISCONNECT_RESP ID=002 #0x001f LEN=0012
Controller/PLCI/NCCI = 0x304
> CAPI INFO 0x3302: Protocol error layer 2
== DIVA2: CAPI Hangingup
== DIVA2: Interface cleanup PLCI=0x304
> CAPI devicestate requested for DIVA2/2
> CAPI devicestate requested for DIVA2/2
-- Incoming call: Got SIP response 500 "Internal Server Error"
back from 10.0.3.138
== Spawn extension (admin, 2131, 2) exited non-zero on
'SIP/0146472130-f4c2'
This queue includes:
member => CAPI/DIVA2/2
I'm not quite sure I got the syntax right for isdn phones in NT mode.
By the way, when two phones are plugged in a Diva port with a Y-plug how
does one dial each phone separately? Do they have an "address"?
--
[EMAIL PROTECTED]
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
