There is no 'sending-complete'/'setup' info-element, please use immediate=yes in capi.conf
Armin On Wed, 11 Jan 2006 [EMAIL PROTECTED] wrote: > Thank you very much for your attention; > Here is what you asked for: > *********************************************************************************** > asteriskge03*CLI> set verbose 15 > Verbosity is at least 15 > asteriskge03*CLI> capi debug > CAPI Debugging Enabled > asteriskge03*CLI> capi info > Contr1: 2 B channels total, 2 B channels free. > > CONNECT_IND ID=002 #0x2011 LEN=0047 > Controller/PLCI/NCCI = 0x101 > CIPValue = 0x1 > CalledPartyNumber = <a1>104695467 > CallingPartyNumber = <21 81>108680550 > CalledPartySubaddress = default > CallingPartySubaddress = default > BC = <80 90 a3> > LLC = default > HLC = default > AdditionalInfo = default > > -- CONNECT_IND > (PLCI=0x101,DID=104695467,CID=108680550,CIP=0x1,CONTROLLER=0x1) > > BRI1: msn='*' DNID='104695467' MSN > == BRI1: Incoming call '0108680550' -> '104695467' > INFO_IND ID=002 #0x2012 LEN=0017 > Controller/PLCI/NCCI = 0x101 > InfoNumber = 0x1e > InfoElement = <82 81> > > INFO_RESP ID=002 #0x2012 LEN=0012 > Controller/PLCI/NCCI = 0x101 > > -- BRI1: info element PI 82 81 > > BRI1: Not end-to-end ISDN > INFO_IND ID=002 #0x2013 LEN=0025 > Controller/PLCI/NCCI = 0x101 > InfoNumber = 0x70 > InfoElement = <a1>104695467 > > INFO_RESP ID=002 #0x2013 LEN=0012 > Controller/PLCI/NCCI = 0x101 > > -- BRI1: info element CALLED PARTY NUMBER > > BRI1: INFO_IND DID digits not used in this state. > INFO_IND ID=002 #0x2014 LEN=0016 > Controller/PLCI/NCCI = 0x101 > InfoNumber = 0x18 > InfoElement = <89> > > INFO_RESP ID=002 #0x2014 LEN=0012 > Controller/PLCI/NCCI = 0x101 > > -- BRI1: info element CHANNEL IDENTIFICATION 89 > DISCONNECT_IND ID=002 #0x2017 LEN=0014 > Controller/PLCI/NCCI = 0x101 > Reason = 0x0 > > DISCONNECT_RESP ID=002 #0x2017 LEN=0012 > Controller/PLCI/NCCI = 0x101 > > -- BRI1: DISCONNECT_IND on incoming without pbx, doing hangup. > == BRI1: CAPI Hangingup > == BRI1: Interface cleanup PLCI=0x101 > > CAPI devicestate requested for BRI1/104695467 > > *********************************************************************************** > > The lines: > > BRI1: DISCONNECT_IND on incoming without pbx, doing hangup. > == BRI1: CAPI Hangingup > == BRI1: Interface cleanup PLCI=0x101 > > CAPI devicestate requested for BRI1/104695467 > > appeared on the console WHILE I was still earing the ring tone on the > calling phone. When I , at last, after other 4 rings, hangup the calling > phone, > nothing changed on the console > > > Andrea > > > > > Armin Schindler > <[EMAIL PROTECTED] > > To > Sent by: Asterisk Users Mailing List - > asterisk-users-bo Non-Commercial Discussion > [EMAIL PROTECTED] <[email protected]> > m.com cc > > Subject > 10/01/2006 19.16 Re: [Asterisk-Users] CHAN_CAPI > problem > > Please respond to > Asterisk Users > Mailing List - > Non-Commercial > Discussion > <[EMAIL PROTECTED] > ists.digium.com> > > > > > > > On Tue, 10 Jan 2006 [EMAIL PROTECTED] wrote: > > Thank you. > > I already downloaded and installed it (they are dated 07-01-2006, version > > 0.6.3, correct ?) > > Yes. > > > I maked clean, make and make install. > > > > Nothing changed, dial out perfect, dial in: (capi debug on) > > > > asteriskge03*CLI> capi info > > Contr1: 2 B channels total, 2 B channels free. > > asteriskge03*CLI> > > asteriskge03*CLI> > > -- CONNECT_IND > > (PLCI=0x101,DID=104695467,CID=108680550,CIP=0x1,CONTROLLER=0x1) > > == BRI1: Interface cleanup PLCI=0x101 > > > > BRI1 is the name of my interface > > > > could it be a kernel issue ?? I am using SUSE Linux 10; > > I don't think so. Please increase the the verbose level to 5 > (set verbose 5) in addition to 'capi debug'. > > Armin > > > kernel : 2.6.13-15.7-smp > > > > Andrea > > > > > > > > > > > Armin Schindler > > > <[EMAIL PROTECTED] > > > > > To > > Sent by: Asterisk Users Mailing List - > > > asterisk-users-bo Non-Commercial Discussion > > > [EMAIL PROTECTED] <[email protected]> > > > m.com > cc > > > > > > Subject > > 10/01/2006 18.29 Re: [Asterisk-Users] CHAN_CAPI > > > problem > > > > > > Please respond to > > > Asterisk Users > > > Mailing List - > > > Non-Commercial > > > Discussion > > > <[EMAIL PROTECTED] > > > ists.digium.com> > > > > > > > > > > > > > > > > > I suggest you use the newer chan_capi-cm (loadable from sourceforge.net). > > > > Armin > > > > On Tue, 10 Jan 2006 [EMAIL PROTECTED] wrote: > > > Hi all, > > > I installed asterisk stable cvs 1.2 and chan_capi 0.4.0 PRE1, with one > > AVM > > > Fritz Card ISDN connected to a Telecom NT1 Plus > > > > > > I configured asterisk via AMP. > > > No problem in making calls. > > > If I try to ring the ISDN Phone Number, I don't see anything on the > > > asterisk Console, > > > I I activate the capi debug , I see the ring on the capi channel. > > > If the context were wrong , I anyway should see some line about > this.... > > > > > > Why I cannot see anything on asterisk ,nor in the > /var/log/asterisk/full > > ? > > > > > > here is my /etc/asterisk/capi.conf > > > > > > asteriskge03:/etc/asterisk # cat capi.conf > > > ; > > > ; CAPI config > > > ; > > > ; > > > > > > ; general section > > > > > > [general] > > > nationalprefix=0 > > > internationalprefix=00 > > > rxgain=0.8 > > > txgain=0.8 > > > ;ulaw=yes ;set this, if you live in u-law world instead of a-law > > > > > > ; interface sections ... > > > > > > [BRI1] ;this example interface gets name 'ISDN1' and may be > any > > > ;name not starting with 'g' or 'contr'. > > > ;ntmode=yes ;if isdn card operates in nt mode, set this to yes > > > isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward > > dial) > > > ;when using NT-mode, 'DID' should be set in any case > > > incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = > any > > > ;defaultcid=123 ;set a default caller id to that interface for > dial-out, > > > ;this caller id will be used when dial option 'd' is > > set. > > > ;controller=0 ;ISDN4BSD default > > > ;controller=7 ;ISDN4BSD USB default > > > controller=1 ;capi controller number to use > > > group=1 ;dialout group > > > ;prefix=0 ;set a prefix to calling number on incoming calls > > > softdtmf=on ;enable/disable software dtmf detection, recommended > for > > > AVM cards > > > relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf > > > detection > > > accountcode= ;Asterisk accountcode to use in CDRs > > > context=from-pstn ;context for incoming calls > > > holdtype=hold ;when Asterisk puts the call on hold, ISDN HOLD will > be > > > used. If > > > ;set to 'local' (default value), no hold is done and > > > Asterisk may > > > ;play MOH. > > > ;immediate=yes ;DID: immediate start of pbx with extension 's' if no > > > digits were > > > ; received on incoming call (no destination number > > > yet) > > > ;MSN: start pbx on CONNECT_IND and don't wait for > > > SETUP/SENDING-COMPLETE. > > > ; info like REDIRECTINGNUMBER may be lost, but > this > > is > > > necessary for > > > ; drivers/pbx/telco which does not send SETUP or > > > SENDING-COMPLETE. > > > ;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression > > > ;echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation > > > ;(possible values: 'no', 'yes', 'force', 'g164', > 'g165') > > > echocancelold=yes;use facility selector 6 instead of correct 8 > (necessary > > > for older eicon drivers) > > > ;echotail=64 ;echo cancel tail setting > > > ;bridge=yes ;native bridging (CAPI line interconnect) if available > > > ;callgroup=1 ;Asterisk call group > > > devices=2 ;number of concurrent calls on this controller > > > ;(2 makes sense for single BRI, 30 for PRI) > > > > > > thanks in advance, > > > Andrea > > > > > > Chi ricevesse questa mail per errore e' gentilmente pregato di > > cancellarla. > > > > > > Visitate il sito http://www.frameweb.it > > > > > > _______________________________________________ > > > --Bandwidth and Colocation provided by Easynews.com -- > > > > > > Asterisk-Users mailing list > > > To UNSUBSCRIBE or update options visit: > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com -- > > > > Asterisk-Users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com -- > > > > Asterisk-Users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
