Here are my findings with my experiment using Sony Erisson T616 with
Cingular Service and connected to [EMAIL PROTECTED] 2.2 on a freshly
installed system and following the instructions
http://www.thetechguide.com/howto/asterisk/chanbluetooth.html
Outbound calls (Asterisk to T616 via bluetooth):
Works OK via Dial(BLT/T616/8005551212)
Inbound calling (T616 to asterisk via bluetooth):
My configuration for inbound calls:
[bluetooth]
exten => s,1,Wait(1)
exten => s,2,Answer
exten => s,3,Dial(SIP/1007,15,rtT)
exten => s,4,VoiceMail([EMAIL PROTECTED])
exten => s,5,Hangup
My observation:
When I call my cell T616 from my landline, SIP/1007 rings for 2
seconds and the call is answered by Cingular voicemail not by asterisk
voicemail. My cingular voicemail is set to answer in 30 seconds after
first ring.
Output on the asterisk CLI:
[EMAIL PROTECTED] ~]# asterisk -r
Asterisk 1.2.1, Copyright (C) 1999 - 2005 Digium.
Written by Mark Spencer <[EMAIL PROTECTED]>
=========================================================================
Connected to Asterisk 1.2.1 currently running on asterisk1 (pid = 3025)
Verbosity is at least 3
[AG] T616 > +CIEV: 2,4
[AG] T616 > +CIEV: 2,3
[AG] T616 > RING
[AG] T616 > +CLIP: "4255551212",161,,,"Landline"
-- Executing Wait("BLT/T616", "1") in new stack
-- Executing Answer("BLT/T616", "") in new stack
[AG] T616 < +CIEV: 2,1
[AG] T616 < +CIEV: 3,0
-- Executing Dial("BLT/T616", "SIP/1007|15|rtT") in new stack
-- Called 1007
-- SIP/1007-d97e is ringing
== Spawn extension (bluetooth, s, 3) exited non-zero on 'BLT/T616'
[AG] T616 < ATH
[AG] T616 < AT+CHUP
[AG] T616 > ERROR
[AG] T616 > OK
[AG] T616 < AT+BRSF=23
[AG] T616 > ERROR
[AG] T616 < AT+CIND=?
[AG] T616 > +CIND:
("battchg",(0-5)),("signal",(0-5)),("batterywarning",(0-1)),("chargerconnected",(0-1)),("service",(0-1)),("sounder",(0-1)),("message",(0-1)),("call",(0-1)),("roam",(0-1)),("smsfull",(0-1))
[AG] T616 > OK
[AG] T616 < AT+CIND?
[AG] T616 > +CIND: 5,3,0,1,1,0,0,0,0,0
[AG] T616 > OK
[AG] T616 < AT+CMER=3,0,0,1
[AG] T616 > OK
[AG] T616 < AT+CLIP=1
[AG] T616 > OK
[AG] T616 < AT+CGMI
[AG] T616 > SONY ERICSSON
[AG] T616 > OK
[AG] T616 < AT+CGMI
[AG] T616 > SONY ERICSSON
[AG] T616 > OK
[AG] T616 > +CIEV: 2,4
[AG] T616 > +CIEV: 2,3
asterisk1*CLI>
On 1/26/06, Nilesh Londhe <[EMAIL PROTECTED]> wrote:
> BTW, I did get clear bidirectional audio when I succeded in dialing
> out...(with the channel = 3 in /etc/asterisk/bluetooth.conf) I have
> Sony Ericsson T616 connected to a cheap commodity bluetooth USB dongle
> that I bought ages ago from meritline.
>
> On 1/26/06, Nilesh Londhe <[EMAIL PROTECTED]> wrote:
> > Thanks a billion.
> >
> > Outbound bluetooth dialling on the lines of
> > Dial(BLT/DevName/8005551212) worked for me.
> >
> > Still trying out the inbound route. Before I created the [bluetooth]
> > context, it tried to reach the [default] context but then I began by
> > creating a new context [bluetooth] in extensions.conf and got my
> > internal SIP phone to ring when I received a call on my SE T616 cell
> > phone. However, I could not get the inbound line answered and I will
> > continue to work on this over the weekend and report back my progress.
> >
> > On 1/25/06, Joseph Tanner <[EMAIL PROTECTED]> wrote:
> > > Again, my documentation is still sparse. I should have noted that the
> > > phone will recognize asterisk and connect even if the channel in
> > > bluetooth.conf is configured wrong. You'll just get no audio, or
> > > disconnects, or what-not until it's set correctly. So realize that
> > > later on when you're testing. Also the usb dongle must have a CSR
> > > chipset, else it won't work (well, at least probably won't work, I'll
> > > provide instructions on how to tell if it should work or not later).
> > >
> > > Here's the relevant instructions on
> > > http://www.crazygreek.co.uk/content/chan_bluetooth for how to dial
> > > out: Send a call out by using Dial(BLT/DevName/0123456).
> > >
> > > As far as dialing in, there's a special context (I think [bluetooth]
> > > maybe? I'll have to get back to you on that). I know that it should
> > > work fine, because I tried dialing the phone, asterisk picked it up
> > > then immediately disconnected because there was no context for it to
> > > go to (I think it tried to fall back on [default], which I didn't have
> > > configured to accept an incoming call).
> > >
> > > Good luck!
> > >
> > > Joseph Tanner
> > >
> > > On 1/26/06, Nilesh Londhe <[EMAIL PROTECTED]> wrote:
> > > > Thanks a lot. I succeeded in pairing my Sony Ericson T616 using your
> > > > instructions at
> > > > http://www.thetechguide.com/howto/asterisk/chanbluetooth.html without
> > > > any problems. I rebooted and the phone prompted me to connect to
> > > > asterisk. I provided the pin 1234 and voila it connected...
> > > >
> > > > Couple of observations:
> > > >
> > > > I started off with clean slate and booted off from [EMAIL PROTECTED]
> > > > 2.2 CD.
> > > > skipped the initial yum -u update part to save some time.
> > > >
> > > > When I ran the "sdptool search --bdaddr MACADDRESS 0x111F" command,
> > > > below is what I got:
> > > >
> > > > Class 0x111F
> > > > Searching on MACADDRESS
> > > > Service Name: HF Voice Gateway
> > > > Service RecHandle: 0x10007
> > > > Service Class ID List:
> > > > "" (0x111f)
> > > > "Generic Audio" (0x1203)
> > > > Protocol Descriptor List:
> > > > "L2CAP" (0x0100)
> > > > "RFCOMM" (0x0003)
> > > > Channel: 6
> > > > Profile Descriptor List
> > > > "" 0x111e
> > > > Version 0x0100
> > > >
> > > > Note that in /etc/asterisk/bluetooth.conf, I kept Channel = 3 (did not
> > > > change it to 6) and it paired my tooth in the first attempt after I
> > > > rebooted asterisk box.
> > > >
> > > > Now, I want to get rid of my Doc-N-Talk that I currently connect my
> > > > T616 to and the other end of Doc-N-Talk goes to x100p.
> > > >
> > > > Although I have worked with linux a bit, I am basically an ASTERISK
> > > > NEWBIE so please pardon my ignorane but I don't know what to do
> > > > next...that is.. how to define this bluetooth channel to make and
> > > > receive calls using this setup...
> > > >
> > > > Appreciate your help.
> > > >
> > > >
> > > > On 1/25/06, Joseph Tanner <[EMAIL PROTECTED]> wrote:
> > > > > Please note this is a work in progress:
> > > > >
> > > > > http://www.thetechguide.com/howto/asterisk/chanbluetooth.html
> > > > >
> > > > > Basically the bluetoothfiles.tar.gz has the cvs code with the Makefile
> > > > > that worked for me, plus the edited Makefile in
> > > > > /usr/src/asterisk/channels, and the bluez edits I needed (hcid.conf
> > > > > with the correct profile, the files needed for the pin which is set to
> > > > > 1234, etc.). The guide is supposed to walk a person through the
> > > > > entire process of getting an Asterisk box setup and bluetooth working,
> > > > > but it's grossly incomplete. Maybe it'll help you out.
> > > > >
> > > > > Joseph Tanner
> > > > >
> > > > > On 1/25/06, Nilesh Londhe <[EMAIL PROTECTED]> wrote:
> > > > > > Hi Joseph:
> > > > > >
> > > > > > >>I still couldn't compile the newest cvs version of
> > > > > > >>chan_bluetooth, so
> > > > > > >>I again tried my trick of using the Makefile from an older version
> > > > > > >>(which used .tmp to compile) and it worked!
> > > > > >
> > > > > > Can you please point to the cvs you used, the location and content
> > > > > > of
> > > > > > pin files you created and paste a copy of the make file that worked
> > > > > > for you?
> > > > > >
> > > > > > Appreciate you sharing this information. Thanks.
> > > > > >
> > > > > > On 1/20/06, Joseph Tanner <[EMAIL PROTECTED]> wrote:
> > > > > > > Ok, I did get this going (somewhat), and in case someone else has
> > > > > > > the
> > > > > > > same issues I'll detail what I had to do.
> > > > > > >
> > > > > > > First, I was using the instructions at
> > > > > > > http://mundy.org/blog/index.php?p=79. They stated that [EMAIL
> > > > > > > PROTECTED]
> > > > > > > 2.2 already had all the rpms necessary for bluetooth and that I
> > > > > > > could
> > > > > > > skip the yum install step. I did, however, run the command
> > > > > > > anyways
> > > > > > > after a few failed attempts. There's an error in the rpm name,
> > > > > > > they
> > > > > > > tell you to install bluez-libs, the correct name is
> > > > > > > bluez-libs-devel
> > > > > > > (at least, that's what I needed to install).
> > > > > > >
> > > > > > > I still couldn't compile the newest cvs version of
> > > > > > > chan_bluetooth, so
> > > > > > > I again tried my trick of using the Makefile from an older version
> > > > > > > (which used .tmp to compile) and it worked! Once compiled, I
> > > > > > > installed and started up asterisk. I then received a message on
> > > > > > > my
> > > > > > > phone asking if I wanted to allow asterisk to connect, and then
> > > > > > > asked
> > > > > > > for a pin. This took a bit of figuring out, but I got passed
> > > > > > > that.
> > > > > > > In /etc/bluetooth/hcid.conf, there's a line that says "pin_helper
> > > > > > > /usr/bin/bluepin;" (it may have a different path, the important
> > > > > > > thing
> > > > > > > is the pin_helper part). Now backup the script in question, i.e.
> > > > > > > in
> > > > > > > my case mv /usr/bin/bluepin /usr/bin/bluepin.bak. Use your
> > > > > > > editor of
> > > > > > > choice to create a new file with the same name, and in it enter:
> > > > > > >
> > > > > > >
> > > > > > > #!/bin/sh -e
> > > > > > > echo "PIN:1234"
> > > > > > >
> > > > > > > Replace the 1234 with whatever you want your pin to be. I don't
> > > > > > > know
> > > > > > > if this is necessary, but I also edited /etc/bluetooth/pin to
> > > > > > > read:
> > > > > > >
> > > > > > > 1234
> > > > > > >
> > > > > > > Again, 1234 should be whatever you want your pin to be. I then
> > > > > > > stopped asterisk, stopped the bluetooth service, started the
> > > > > > > bluetooth
> > > > > > > service back up, started asterisk, then when my phone asked for a
> > > > > > > pin
> > > > > > > I put in 1234, and it worked!
> > > > > > >
> > > > > > > You may also need to make another edit to hcid.conf, under Local
> > > > > > > Device Class change it to read class "0x200404;" or possibly
> > > > > > > "class
> > > > > > > 0x700408;". This makes your bluetooth dongle look like a
> > > > > > > headset, and
> > > > > > > not a data device (I experienced some flakiness until I changed
> > > > > > > this).
> > > > > > >
> > > > > > > Now, I edited /etc/asterisk/bluetooth.conf appropriately (changed
> > > > > > > the
> > > > > > > channel for the phone to 7, it's a Motorola V551), started it all
> > > > > > > up,
> > > > > > > made some test calls and...no audio! The cellphone works great
> > > > > > > otherwise. It'll connect, stay connected as long as I want it
> > > > > > > to, and
> > > > > > > when I hang up the asterisk extension the cellphone will
> > > > > > > disconnect
> > > > > > > too. Too bad I didn't realize 611 was a free call until after I
> > > > > > > made
> > > > > > > a lot of test calls (it's a prepaid phone). I did call our home
> > > > > > > number directly to see if maybe I just had a one-way audio
> > > > > > > problem,
> > > > > > > but nobody could hear a thing on either end. I will continue to
> > > > > > > troubleshoot this before I ask another question about it, but
> > > > > > > it's not
> > > > > > > looking good. BTW, the usb dongle I'm using is a Linksys
> > > > > > > USBBT100.
> > > > > > > _______________________________________________
> > > > > > > --Bandwidth and Colocation provided by Easynews.com --
> > > > > > >
> > > > > > > Asterisk-Users mailing list
> > > > > > > To UNSUBSCRIBE or update options visit:
> > > > > > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > > > > >
> > > > > > _______________________________________________
> > > > > > --Bandwidth and Colocation provided by Easynews.com --
> > > > > >
> > > > > > Asterisk-Users mailing list
> > > > > > To UNSUBSCRIBE or update options visit:
> > > > > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > > > >
> > > > > _______________________________________________
> > > > > --Bandwidth and Colocation provided by Easynews.com --
> > > > >
> > > > > Asterisk-Users mailing list
> > > > > To UNSUBSCRIBE or update options visit:
> > > > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > > >
> > > > _______________________________________________
> > > > --Bandwidth and Colocation provided by Easynews.com --
> > > >
> > > > Asterisk-Users mailing list
> > > > To UNSUBSCRIBE or update options visit:
> > > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > >
> > > _______________________________________________
> > > --Bandwidth and Colocation provided by Easynews.com --
> > >
> > > Asterisk-Users mailing list
> > > To UNSUBSCRIBE or update options visit:
> > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > >
> >
>
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
