Hi Steve
May I change TX ABCD bits 0101 to 1001 or no ? -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Steve Underwood Sent: Wednesday, February 22, 2006 3:28 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Tormenta CAS signaling Hi Viktor, So? You seem to have 5 channels set to fxols mode OK. What exactly that does, I am not sure. FXO operation is highly telco dependent with E1s. I believe what is implemented in zaptel is an arrangement to work with some E1 channel banks. Do you have an actual question this time? Steve Viktor Tatianin wrote: >Hi Steve >I have next config >zttool > >Current Alarms: No alarms. >Sync Source: Tormenta 2 (PCI) Quad E1 Card >IRQ Misses: 0 >Bipolar Viol: 14 >Tx/Rx Levels: 0/ 0 > >Total/Conf/Act: 31/ 6/ 6 > 1111111111222222222333 > 1234567890123456789012345789012 > > TxA 000000 > TxB 111111 > TxC 000000 > TxD 111111 > > RxA 111111 > RxB 011111 > RxC 011111 > RxD 111111 > > > > > > > >ztcfg -vv > >Zaptel Configuration >====================== > >SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) >SPAN 2: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) > >Channel map: > >Channel 01: Clear channel (Default) (Slaves: 01) >Channel 02: Clear channel (Default) (Slaves: 02) >Channel 03: Clear channel (Default) (Slaves: 03) >Channel 04: Clear channel (Default) (Slaves: 04) >Channel 05: Clear channel (Default) (Slaves: 05) >Channel 06: Clear channel (Default) (Slaves: 06) >Channel 07: Clear channel (Default) (Slaves: 07) >Channel 08: Clear channel (Default) (Slaves: 08) >Channel 09: Clear channel (Default) (Slaves: 09) >Channel 10: Clear channel (Default) (Slaves: 10) >Channel 11: Clear channel (Default) (Slaves: 11) >Channel 12: Clear channel (Default) (Slaves: 12) >Channel 13: Clear channel (Default) (Slaves: 13) >Channel 14: Clear channel (Default) (Slaves: 14) >Channel 15: Clear channel (Default) (Slaves: 15) >Channel 16: D-channel (Default) (Slaves: 16) >Channel 17: Clear channel (Default) (Slaves: 17) >Channel 18: Clear channel (Default) (Slaves: 18) >Channel 19: Clear channel (Default) (Slaves: 19) >Channel 20: Clear channel (Default) (Slaves: 20) >Channel 21: Clear channel (Default) (Slaves: 21) >Channel 22: Clear channel (Default) (Slaves: 22) >Channel 23: Clear channel (Default) (Slaves: 23) >Channel 24: Clear channel (Default) (Slaves: 24) >Channel 25: Clear channel (Default) (Slaves: 25) >Channel 26: Clear channel (Default) (Slaves: 26) >Channel 27: Clear channel (Default) (Slaves: 27) >Channel 28: Clear channel (Default) (Slaves: 28) >Channel 29: Clear channel (Default) (Slaves: 29) >Channel 30: Clear channel (Default) (Slaves: 30) >Channel 31: Clear channel (Default) (Slaves: 31) >Channel 32: FXO Loopstart (Default) (Slaves: 32) >Channel 33: FXO Loopstart (Default) (Slaves: 33) >Channel 34: FXO Loopstart (Default) (Slaves: 34) >Channel 35: FXO Loopstart (Default) (Slaves: 35) >Channel 36: FXO Loopstart (Default) (Slaves: 36) >Channel 37: FXO Loopstart (Default) (Slaves: 37) > >37 channels configured. > >this is zaptel.conf > >; Zapata telephony interface >; >; Configuration file > >[trunkgroups] > >[channels] > >language=en >context=from-isdn-external >;signalling=fxs_ks >;rxwink=300 ; Atlas seems to use long (250ms) winks >signalling=pri_cpe >switchtype=euroisdn >pridialplan=unknown >prilocaldialplan=unknown >callerid=asreceived >usedistinctiveringdetection=yes >usecallingpres=yes > >; Whether or not to do distinctive ring detection on FXO lines >; >;usedistinctiveringdetection=yes > >usecallerid=yes >hidecallerid=no >callwaiting=yes >usecallingpres=yes >callwaitingcallerid=yes >threewaycalling=yes >transfer=yes >cancallforward=yes >callreturn=yes >echocancel=yes >echocancelwhenbridged=yes >echotraining=400 >rxgain=0.0 >txgain=0.0 >group=0 >callgroup=1 >pickupgroup=1 >immediate=no > >;faxdetect=both >faxdetect=incoming >;faxdetect=outgoing >;faxdetect=no > >;Include genzaptelconf configs >#include zapata-auto.conf > >;Include AMP configs >#include zapata_additional.conf >channel=> 1-15,17-31 > >signalling=fxo_ks >context=bank >group=1 >cas=32-37:1101 >channel=> 32-37 >This is my zapata.conf > ># Global data > >span=1,1,0,ccs,hdb3 >bchan=1-15,17-31 >dchan=16 > >loadzone = us >defaultzone = us > >span=2,1,0,cas,hdb3 >fxols=32-37 > > > > >-----Original Message----- >From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED] Behalf Of Steve Underwood >Sent: Tuesday, February 21, 2006 2:59 PM >To: Asterisk Users Mailing List - Non-Commercial Discussion >Subject: Re: [Asterisk-Users] Tormenta CAS signaling > > >Viktor Tatianin wrote: > > > >>Hi Steve >> >>I attempt change in zapata.conf >> >>cas=1-15:1101 but use zttool view ABCD bits 1010 >> >>Regards, >>Viktor >> >> >> >> >Have you put the E1 in CAS mode with something like: > >span=1,1,0,cas,hdb3 > >Steve > > > >>-----Original Message----- >>From: [EMAIL PROTECTED] >>[mailto:[EMAIL PROTECTED] Behalf Of Steve >> >> >Underwood > > >>Sent: Friday, February 10, 2006 3:25 PM >>To: Asterisk Users Mailing List - Non-Commercial Discussion >>Subject: Re: [Asterisk-Users] Tormenta CAS signaling >> >> >>Viktor Tatianin wrote: >> >> >> >> >> >>>Hello >>> >>>Can anyone know how may change(inverting) cas signaling ABCD bits at the >>>Tormenta 2 (four E1 ports) cards >>>My cards send idle code ABCD 0101 but my mux which use as channel bank >>> >>> >wait > > >>>ABCD 1001 >>> >>> >>> >>> >>> >>> >>The idle code is set in zapata.conf. For example: >> >>cas=1-15:1101 >> >>Sets CAS mode for channels 1 to 15, with the idle pattern 1101. >> >>Regards, >>Steve >> >> >> >> > >_______________________________________________ >--Bandwidth and Colocation provided by Easynews.com -- > >Asterisk-Users mailing list >To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > >_______________________________________________ >--Bandwidth and Colocation provided by Easynews.com -- > >Asterisk-Users mailing list >To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
