Alban wrote:
Hello,
Have you tried to delete rtnoupdate and rtautoclear lines? I'm using realtime,
with caching for sip but without those 2 lines, and works perfectly.
Another point : verify that you have the field fullcontact in your realtime
sip table.
Bye,
Alban Elziere
While I compiled the message, I discovered the difference already in
canreinvite=yes/no
I could test it, and it was the problem!
I found than that if you have the phones behind asterisk you MUST have
canreinvite=no to force, the rtp stream to go through asterisk and not
to try to bypass it. I use bypass so that the users are directly
connected to the gateways without bothering my servers bandwidth.
rtnoupdate=yes
; do not send the update request over realtime.
rtautoclear=yes
; Auto-Expire friends created on the fly on the same schedule
; as if it had just registered when the registration expires
; the friend will vanish from the configuration until requested
; again. If set to an integer, friends expire
; within this number of seconds instead of the
; same as the registration interval
I have two phones (111 and 112) on a LAN, and I have on a users site a
phone 333.
phone 111 uses sip.conf, while 112 uses real-time set-up.
111 can call 333 AND the audio is working
112 can call 333 but audio is just white noise.
333 can call 111 or 112 and audio is working.
The phones are identically set-up (just user name = phone number and
password are different)
sip.conf (for 111 - all remarked lines removed)
[general]
context=default ; Default context for incoming calls
port=5060 ; UDP Port to bind to (SIP standard port is 5060)
bindaddr=0.0.0.0 ; IP address to bind to (0.0.0.0 binds to all)
srvlookup=yes ; Enable DNS SRV lookups on outbound calls
tos=lowdelay ;
lowdelay,throughput,reliability,mincost,none
maxexpirey=7200 ; Max length of incoming registration we allow
defaultexpirey=3600 ; Default length of incoming/outoing
registration videosupport=yes ; Turn on support for SIP video
disallow=all ; First disallow all codecs
allow=ulaw ; Allow codecs in order of preference
allow=alaw
allow=g729
allow=gsm
rtcachefriends=yes
rtnoupdate=yes
rtautoclear=yes
externip = 59.14.2.1
localnet=192.168.0.0/255.255.0.0; All RFC 1918 addresses are local networks
[111]
type=friend
username=hotline
secret=I-know-it
canreinvite=no
host=dynamic
dtmfmode=rfc2833
[EMAIL PROTECTED]
nat=yes
callgroup=1
pickupgroup=1
callerid="Ronald Hotline",<111>
qualify=1000
Real-time for 112:
name=112
callerid="Ronald Hotline",<112>
canreinvite=yes
context=default
dtmfmode=rfc2833
host=dynamic
language=en
[EMAIL PROTECTED]
nat=yes
pickupgroup=1
port=5060
qualify=1000
secret=I-know-it
type=friend
username=112
disallow=all
allow=ulaw;alaw;g729;gsm
cancallforward=yes
Which of the settings cause the different behaviour?
Which settings should I change (maybe not related to the problem)?
bye
Ronald
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
Ronald Wiplinger (CEO of ELMIT)
http://www.elmit.com http://voip.elmit.com http://e-paper.elmit.com
Tel. (M) +886.939.775.516 (O) +886.2.2835.7765 (ENUM) or FWD 511208
- I'm a SpamCon Foundation Member, #694, Verify it at http://www.spamcon.org
PS: Spam prevention!
Our system is protected with a spam prevention program.
If you send us an e-mail, our system will send you a confirmation message back. Just reply to this confirmation message please.
After receiving this confirmation message, our system will send the hold message (one) and all future messages (after the received confirmation message) to me without asking you again.
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
