On 4/18/06, Damon Estep <[EMAIL PROTECTED]> wrote: > Yep, > > I agree, > > Just watch out for regulatory issues if you are in the USA, handing a > CUSTOMER a TDM interface vs. a SIP/VoIP interface falls under a much > different regulatory and jurisdictional set of rules...
regulatory issues only apply if I'm a provider, this is all for implementing a private circuit. > > Have you talked to anyone that has confirmed an implementation like > described works without issues? not as a PRI, but I have done this with 2 Adit 600s like this: Site A Definity 3G System <> Analog station cards <> Adit 600 FXO Card and router card <> Private full T1 circuit to longdistance haul <> Site B <> Adit 600 FXS Card and router card. With the above config we got analog extensions of our Avaya system, and a local network routed over the left over channells (IIRC we did 12 data and 12 voice, all provisioned from the Adit 600s). > > Damon > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:asterisk-users- > > [EMAIL PROTECTED] On Behalf Of C F > > Sent: Tuesday, April 18, 2006 12:31 PM > > To: Asterisk Users Mailing List - Non-Commercial Discussion > > Subject: Re: [Asterisk-Users] T1 to cross connect remote PBX and > asterisk > > > > In theory it should work, I have just written a proposal for someone > > that involves such a setup. in worst case I can always utilize the > > circuit as data, and use 2 asterisk boxes one on each end to convert > > it back to NI2. > > > > On 4/18/06, Damon Estep <[EMAIL PROTECTED]> wrote: > > > > > > > > > > > > Looking for someone with a successful experience similar to this; > > > > > > > > > > > > I have a need to cross connect a 3COM NBX PBX PRI interface to > asterisk, > > but > > > over a long distance. We do not need any IP connectivity and the > > solution > > > requires G.711u audio so there is no benefit to using IP. > > > > > > > > > > > > Has anyone here successfully cross connected any PBX PRI interface > > expecting > > > NI2 PRI signaling B8ZS/ESF with an asterisk box providing > PRI_Network > > > signaling on a T1 interface card using a long haul point to point > > ESF/B8ZS > > > T1? > > > > > > > > > > > > I do not need the technical details on how to set up asterisk or the > > remote > > > PBX, just need a sanity check on the idea of using the PTP T1 as a > cross > > > connect facility. If they were local to each other I would simply > drop > > in a > > > T1 crossover cable, but they are not J > > > > > > > > > > > > Thanks! > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > _______________________________________________ > > > --Bandwidth and Colocation provided by Easynews.com -- > > > > > > Asterisk-Users mailing list > > > To UNSUBSCRIBE or update options visit: > > > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > > > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com -- > > > > Asterisk-Users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
