(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not)
Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1, closest to the bracket. This appears to be the failing component. FXO (red) module is in position 4, furthest from the bracket ------------ >From what I can gather it's just the FXS module that is failing, and not the card. What I was hoping someone could tell me is whether the whole card is U/S or just that module, based on the information I have provided below. Any help will be greatly appreciated. Thanks, Nigel The interesting parts of the zapata.conf are: ------------------ ; The FXS port, or the "phone" port signalling=fxo_ks echocancel=yes ; You can set this to 32, 64, or 128, tweak to your needs. echocancelwhenbridged=yes echotraining=400 ; Asterisk trains to the beginning of the call, number is in milliseconds [EMAIL PROTECTED] group=1 context=outgoing ; Points to the default context of your extensions.conf channel => 1 usecallerid=no ;cidsignalling=bell ;cidstart=ring ;hidecallerid=no callwaiting=yes ; The FXO port, or the "line" port signalling=fxs_ks group=2 ;rxwink=300 ; Atlas seems to use long (250ms) winks ;hanguponpolarityswitch ; doesn't work on ADSL lines busydetect=yes busycount=3 context=incoming-pstn channel=> 4 ; Again change the 'X' to the number of FXO modules you have usedistinctiveringdetection=no usecallerid=no ;sendcalleridafter=2 ;cidsignalling=bell ;cidstart=ring ;hidecallerid=no ;restrictcid=no callwaiting=yes -------------------- The asterisk failure is ------------- Apr 27 10:00:46 splash asterisk[14625]: WARNING[14625]: chan_zap.c:923 in zt_open: Unable to specify channel 1: No such device Apr 27 10:00:46 splash asterisk[14625]: ERROR[14625]: chan_zap.c:6878 in mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Apr 27 10:00:46 splash asterisk[14625]: ERROR[14625]: chan_zap.c:10314 in setup_zap: Unable to register channel '1' Apr 27 10:00:46 splash asterisk[14625]: WARNING[14625]: loader.c:414 in __load_resource: chan_zap.so: load_module failed, returning -1 Apr 27 10:00:46 splash asterisk[14625]: WARNING[14625]: loader.c:554 in load_modules: Loading module chan_zap.so failed! ---------------- And asterisk promptly dies. If I execute the following: ------------ # ztcfg -vvvvvv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 2 channels configured. ---------- You can see that the channels are configured OK. And the output from the following commands is a little strange as well: ------------- # cat /dev/zap/1 cat: /dev/zap/1: No such device # cat /dev/zap/2 cat: /dev/zap/2: No such device or address # cat /dev/zap/3 cat: /dev/zap/3: No such device or address # cat /dev/zap/4 (And lots of stuff gets spewed out onto the screen) -------------- _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
