Hi Josue and list,
This is part of my dmesg log. Also one other thing, I don't know why the red
light
on span/port 1 of my card keep flashing.. is it normal that way? Or it's
supposed to
mean something? Obviously I have no experience with ISDN before so this is my
very
first try.
Found TE2XXP at base address e7001000, remapped to e001a000
TE2XXP version c01a0164, burst OFF, slip debug: OFF
FALC version: 00000005, Board ID: 00
Reg 0: 0x1e6ab400
Reg 1: 0x1e6ab000
Reg 2: 0xffffffff
Reg 3: 0x00000000
Reg 4: 0x00000000
Reg 5: 0x00000000
Reg 6: 0xc01a0164
Reg 7: 0x00001000
Reg 8: 0x00000000
Reg 9: 0x00ff0000
Reg 10: 0x00000000
TE2XXP: Launching card: 0
TE2XXP: Setting up global serial parameters
Found a Wildcard: Wildcard TE205P
About to enter spanconfig!
Done with spanconfig!
Registered tone zone
About to enter startup!
TE2XXP: Span 1 configured for ESF/B8ZS
wct2xxp: Setting yellow alarm on span 1
2G: Got interrupt, status = 0000000d, GIS = 0081
SPAN 1: Primary Sync Source
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
VPM: Not Present
Completed startup!
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
About to enter spanconfig!
About to enter startup!
TE2XXP: Span 1 configured for ESF/B8ZS
SPAN 1: Primary Sync Source
Completed startup!
Registered tone zone
About to enter spanconfig!
About to enter startup!
TE2XXP: Span 1 configured for ESF/B8ZS
SPAN 1: Primary Sync Source
Completed startup!
Registered tone zone
About to enter spanconfig!
About to enter startup!
TE2XXP: Span 1 configured for ESF/B8ZS
SPAN 1: Primary Sync Source
Completed startup!
Registered tone zone
--- Josué Conti <[EMAIL PROTECTED]> wrote:
Hi, test with dmesg and past in list the log´s
Regards
Josué
2006/5/10, azyuky <[EMAIL PROTECTED]>:
Hi guys,
Currently I just purchased the TE205P for the installation of my ISDN30
setup. I
compiled, setup the card correctly I think. When I do the ztcfg -vvv it
shows all 31
channels clear, with 30 bchannels using for voice ranging from 1-15,
17-31, and 16
is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24
channels
configured, and then, when I do a cat /proc/zaptel/2 I see the rest 7
channels. I
setup the jumper correctly all closed to use the card in E1 mode.. I'm not
sure what
I did wrong here but the card should just display all 31 channels on span
1
(/proc/zaptel/1) instead of spreading it accross to the second span?
Help is appreciated. Thank you.
