FXS or FXO? Michael Crown Managing Partner www.thevoipconnection.com 321.989.6728 ext. 611 sip:[EMAIL PROTECTED]
> -----Original Message----- > From: William Piper [mailto:[EMAIL PROTECTED] > Sent: Wednesday, May 24, 2006 6:27 PM > To: 'Asterisk Users Mailing List - Non-Commercial Discussion' > Subject: RE: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP > > Sorry to hijack your thread. > > Reading these posts made me grab my old MP-104 & try again to > get it working with asterisk. I bought it a while ago off > eBay & never could get it to register. > > Does anyone have an example ini file for the MP-1XX that I > could look at & figure out what I am configuring wrong on this box? > > Thanks, > > bp > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of > Jerry Jones > Sent: Wednesday, May 24, 2006 6:04 PM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP > > From my copy of the manual > > > MP-1xx SIP User's Manual 36 Document #: LTRT-65404 You can > use the 'Reset' button to restore the MP-1xx networking > parameters to their factory default values (described in > Table 4-1) and to reset the username and password. > Note that the MP-1xx returns to the software version burned > in flash. > This process also restores > the MP-1xx parameters to their factory settings, therefore > you must load your previously backed- up ini file, or the > default ini file (received with the software kit) to set them > to their correct values. > To restore networking parameters to their initial state, take these 6 > steps: > 1. Disconnect the MP-1xx from the power and network cables. > MP-1xx SIP User's Manual 4. Getting Started 2. Reconnect the > power cable; the gateway is powered up. After approximately > 45 seconds the Ready LED turns to green and the Control LED > blinks for about 3 seconds. > 3. While the Control LED is blinking, press shortly on the > reset button (located on the left side of the front panel); > the gateway resets a second time and is restored with factory > default parameters (username: "Admin", password: "Admin"). > 4. Reconnect the network cable. > 5. Assigning the MP-1xx IP address (refer to Section 4.1 on page 35). > 6. Load your previously backed-up ini file, or the default > ini file (received with the software kit). > To load the ini file via the Embedded Web Server, refer to Section > 5.9.2.1 on page 120. > > > > > On May 24, 2006, at 3:00 PM, Erick Perez wrote: > > > Just a question, has anyone knows how to blank or factory reset an > > AudioCodes MP124-C/FSX/AC/SIP unit (it's a 24 FSX to SIP unit). > > I purchased them second-handed with no manuals (thank god for the > > internet!!) but i guess the pdf manual I have does not have the > > section of factory-reset. > > > > Also, any sucess stories with: > > AudioCodes MP124-C/FSX/AC/SIP > <--->Asterisk<---internet<--->Vonage > > setups? > > > > Thanks, > > > > > > -- > > > > ------------------------------------------- > > Erick Perez > > Linux User 376588 > > http://counter.li.org/ (Get counted!!!) Panama, Republic of Panama > > _______________________________________________ > > > > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
