The call is rejected by Asterisk, so it looks like your dialplan has no rule for accepting calls to '99546476'.
Armin On Mon, 5 Jun 2006, Esteban Guana-Jarrin wrote: > I have a problem receving calls via the ISDN line, using the followin > components > > Asterisk 1.0.9 with [EMAIL PROTECTED] > chan_capi-cm-0.6 > AVM Fritz card > datalink protocol = point to multimode > > I can make calls out with no problems so the issue is only incoming calls. > > When I make the call from an external line to the ISDN line connected to > asterisk, I get a busy signal after about 5 seconds. I have read previous > posts from the list and I made sure I have the settings in my capi.conf and > extensions.conf according to all the suggestions and as shown below, > > Capi.conf: > > [general] > nationalprefix=0 > internationalprefix=00 > rxgain=0.8 > txgain=0.8 > ulaw=yes ;set this, if you live in u-law world instead of a-law > > [ISDN1] ;this example interface gets name 'ISDN1' and may be any > ;name not starting with 'g' or 'contr'. > > isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial) > ;when using NT-mode, ptp should be set in any case > msn=0299546476 > incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * == any > controller=1 ;capi controller number to use > group=2 ;dialout group > context=capi-in ;context for incoming calls > immediate=yes ;immediate start of pbx with extension 's' if no digits were > ;received on incoming call (no destination number yet) > devices=2 ;number of concurrent calls on this controller > ;(2 makes sense for single BRI, 30 for PRI) > > In Extensions.conf > > [capi-in] > exten => s,1,Dial(Sip/123,20) > exten => s,2,Voicemail(123) > exten => s,3,Hangup > > Also the Capi debug output with verbosity 15, is shown below. I can see that > after the channel identification message and then the sending complete > message, a DISCONNECT_IND comes straight after and it does not provide any > reasons... > > CAPI Debugging Enabled > CONNECT_IND ID=001 #0x03a6 LEN=0037 > Controller/PLCI/NCCI = 0x101 > CIPValue = 0x10 > CalledPartyNumber = <c1>99546476 > CallingPartyNumber = default > CalledPartySubaddress = default > CallingPartySubaddress = default > BC = <80 90 a3> > LLC = default > HLC = <91 81> > AdditionalInfo = default > > -- CONNECT_IND (PLCI=0x101,DID=99546476,CID=(null),CIP=0x10,CONTROLLER=0x1) > > ISDN1: msn='*' DNID='99546476' MSN > == ISDN1: Incoming call '' -> '99546476' > INFO_IND ID=001 #0x03a7 LEN=0024 > Controller/PLCI/NCCI = 0x101 > InfoNumber = 0x70 > InfoElement = <c1>99546476 > > INFO_RESP ID=001 #0x03a7 LEN=0012 > Controller/PLCI/NCCI = 0x101 > > -- ISDN1: info element CALLED PARTY NUMBER > > ISDN1: INFO_IND DID digits not used in this state. > INFO_IND ID=001 #0x03a8 LEN=0016 > Controller/PLCI/NCCI = 0x101 > InfoNumber = 0x18 > InfoElement = <89> > > INFO_RESP ID=001 #0x03a8 LEN=0012 > Controller/PLCI/NCCI = 0x101 > > -- ISDN1: info element CHANNEL IDENTIFICATION 89 > INFO_IND ID=001 #0x03a9 LEN=0016 > Controller/PLCI/NCCI = 0x101 > InfoNumber = 0xa1 > InfoElement = <a1> > > INFO_RESP ID=001 #0x03a9 LEN=0012 > Controller/PLCI/NCCI = 0x101 > > -- ISDN1: info element Sending Complete > CONNECT_RESP ID=001 #0x03a9 LEN=0032 > Controller/PLCI/NCCI = 0x101 > Reject = 0x1 > BProtocol > B1protocol = 0x0 > B2protocol = 0x0 > B3protocol = 0x0 > B1configuration = default > B2configuration = default > B3configuration = default > ConnectedNumber = default > ConnectedSubaddress = default > LLC = default > AdditionalInfo > BChannelinformation = default > Keypadfacility = default > Useruserdata = default > Facilitydataarray = default > > DISCONNECT_IND ID=001 #0x03aa LEN=0014 > Controller/PLCI/NCCI = 0x101 > Reason = 0x0 > > DISCONNECT_RESP ID=001 #0x03aa LEN=0012 > Controller/PLCI/NCCI = 0x101 > > == ISDN1: CAPI Hangingup > == ISDN1: Interface cleanup PLCI=0x101 > > I will apreciate your assistance > > Esteban > > _________________________________________________________________ > New year, new job there's more than 100,00 jobs at SEEK > http://a.ninemsn.com.au/b.aspx?URL=http%3A%2F%2Fninemsn%2Eseek%2Ecom%2Eau&_t=752315885&_r=Jan05_tagline&_m=EXT > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
_______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
