> That is possible, how could I check that? > I can see that IRQ 17 is shared between eth0 and my fritz!card but I > don't know if it changes anything:
Can you try it (or eth0) in a different slot (or change IRQ's in the BIOS if possible) to see if it makes any difference? That's the only way to know for sure, anything else is just speculation :) James > > ~# cat /proc/interrupts > CPU0 > 0: 1458224031 IO-APIC-edge timer > 1: 953 IO-APIC-edge i8042 > 7: 0 IO-APIC-edge parport0 > 8: 1 IO-APIC-edge rtc > 9: 1 IO-APIC-level acpi > 14: 689691 IO-APIC-edge ide0 > 15: 24 IO-APIC-edge ide1 > 16: 1457845530 IO-APIC-level uhci_hcd:usb1, wctdm > 17: 721402147 IO-APIC-level fcpci, eth0 > 18: 1457844720 IO-APIC-level uhci_hcd:usb3, wctdm > 19: 0 IO-APIC-level uhci_hcd:usb2 > 23: 0 IO-APIC-level ehci_hcd:usb4 > NMI: 0 > LOC: 1458419318 > ERR: 0 > MIS: 0 > > > Benjamin > > > > > > > > > > > > > > > Thanks, > > > > > > > > > > Ben > > > > > > > > > > </etc/asterisk/capi.conf> > > > > > [general] > > > > > rxgain=0.5 > > > > > txgain=0.5 > > > > > language=fr ;set default language > > > > > ;ulaw=yes ;set this, if you live in u-law world > > instead of > > > > a-law > > > > > [ISDN1] > > > > > > > > > > isdnmode=DID ;'MSN' (point-to-multipoint) or 'DID' > > (direct > > > > inward dial) > > > > > ;when using NT-mode, 'DID' should be set in > > any > > > > case> incomingmsn=* ;allow incoming calls to this list of > > > > MSNs/DIDs, * = any > > > > > controller=1 ;capi controller number to use > > > > > group=9 ;dialout group > > > > > softdtmf=on ;enable/disable software dtmf detection, > > > > recommended> for AVM cards > > > > > relaxdtmf=on ;in addition to softdtmf, you can use > > relaxed dtmf > > > > > detection > > > > > accountcode= ;Asterisk accountcode to use in CDRs > > > > > context=capi-in ;context for incoming calls > > > > > ;echosquelch=2 ;_VERY_PRIMITIVE_ echo suppression > > > > > echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation > > > > > ;(possible values: 'no', 'yes', 'force', > > 'g164', > > > > 'g165')> echocancelold=no ;use facility selector 6 instead of > > > > correct 8 > > > > > (necessary for older eicon drivers) > > > > > echotail=128 ;echo cancel tail setting > > > > > devices=2 ;number of concurrent calls on this controller > > > > > ;(2 makes sense for single BRI, 30 for PRI) > > > > > > > > > > _______________________________________________ > > > > > --Bandwidth and Colocation provided by Easynews.com -- > > > > > > > > > > Asterisk-Users mailing list > > > > > To UNSUBSCRIBE or update options visit: > > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > > > > _______________________________________________ > > > > --Bandwidth and Colocation provided by Easynews.com -- > > > > > > > > Asterisk-Users mailing list > > > > To UNSUBSCRIBE or update options visit: > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > > _______________________________________________ > > > --Bandwidth and Colocation provided by Easynews.com -- > > > > > > Asterisk-Users mailing list > > > To UNSUBSCRIBE or update options visit: > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com -- > > > > Asterisk-Users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
