Try using "testcall" tool included with Unicall to debug, as shown in this document I wrote a couple of months ago. It also shows how to use zttool to detect problems in the E1 layer.
http://moy.ivsol.net/unicall/mfcr2-asterisk-unicall-0.2-english.pdf The verbosity level in testcall.c must be at highest level to be able to see the problem clearly. If you have more that 1 port in your PCI cards, try using a loop, like explained in the document, to discard problems on your side. Regards On 10/9/06, Carlos Chavez <[EMAIL PROTECTED]> wrote:
On Mon, 2006-10-09 at 19:39 -0500, Moises Silva wrote: > Same problem as your other post. dtmf_put is no longer available in > newer spandsp versions, the solutions is the same as with libmfcr2, > downgrade spandsp, or upgrade chan_unicall (not always a matching Ok, I downgraded all the programs and now everything compiles. Now I cannot make or receive any calls. When I dial a Unicall channel I can hear a crack on the phone and after a few seconds it gives me a busy tone. I have never had this much trouble installing mfcr2 but I usually use CentOS instead of FC5. I had to use FC5 because the drivers for Xorcom do not compile in CentOS. -- Executing Set("SIP/139-091cd588", "TIMEOUT(absolute)=900") in new stack -- Channel will hangup at 2006-10-10 01:22:54 UTC. -- Executing Dial("SIP/139-091cd588", "Unicall/g1/0445529613670") in new stack Oct 9 20:07:54 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Call control(1) Oct 9 20:07:54 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Make call Oct 9 20:07:54 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Making a new call with CRN 32770 Oct 9 20:07:54 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 0001 -> [1/ 1/Idle /Idle ] -- Called g1/0445529613670 Oct 9 20:07:54 WARNING[19096]: chan_unicall.c:2644 handle_uc_event: Unicall/1 event Dialing Oct 9 20:07:54 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1101 [1/ 40/Seize /Idle ] Oct 9 20:07:54 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 0 on -> [2/ 40/Group I /Idle ] Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 4 on [2/ 40/Group I /DNIS ] Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 0 off -> [2/ 40/Group I /DNIS ] Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 4 off [2/ 40/Group I /DNIS ] Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Far end disconnected(cause=Switching equipment congestion [42]) - state 0x40 Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:2644 handle_uc_event: Unicall/1 event Far end disconnected Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:2930 handle_uc_event: CRN 32770 - far disconnected cause=Switching equipment congestion [42] -- Channel 0 got hangup -- UniCall/1-1 is circuit-busy Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Channel gains Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Channel switching Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Call control(6) Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Drop call(cause=Normal Clearing [16]) Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Clearing fwd Oct 9 20:08:12 WARNING[19096]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 1001 -> [2/ 800/Clear fwd B /DNIS ] -- Hungup 'UniCall/1-1' == Everyone is busy/congested at this time (1:0/1/0) -- Executing Congestion("SIP/139-091cd588", "") in new stack == Spawn extension (oficina-todo, 90445529613670, 3) exited non-zero on 'SIP/139-091cd588' Oct 9 20:08:12 WARNING[19062]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1001 [1/ 800/Clear fwd D /Idle ] Oct 9 20:08:12 WARNING[19062]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Call disconnected(cause=Switching equipment congestion [42]) - state 0x800 Oct 9 20:08:12 WARNING[19062]: chan_unicall.c:2644 handle_uc_event: Unicall/1 event Drop call Oct 9 20:08:12 WARNING[19062]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Call control(7) Oct 9 20:08:12 WARNING[19062]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Release call Oct 9 20:08:12 WARNING[19062]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Destroying call with CRN 32770 Oct 9 20:08:12 WARNING[19062]: chan_unicall.c:2644 handle_uc_event: Unicall/1 event Release call -- Unicall/1 released Oct 9 20:08:12 WARNING[19062]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Channel echo cancel -- Carlos Chavez Prats Director de Tecnología Telecomunicaciones Abiertas de México S.A. de C.V. Tel: +52-55-91169161 Ext 2001 _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
-- "Su nombre es GNU/Linux, no solamente Linux, mas info en http://www.gnu.org" _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users