Hello, The problem was wrong contexts defined like Marco said, and is solved. Now, i have another problem...of course :)
On incoming calls, i only can receive calls if i define a line like the following, in extensions.conf: exten => _.,n,Dial(SIP/500,30,tr) (all incoming calls are redirected to extension 500). The problem is that i have some DDI's assigned by my telco (xxx302500 to xxx302509) and i need to route each DDI to diferent internal extension. If i define someting like "exten => _XXXXXXXX0,n,Dial..." (for DDI xxx302500) the call is not answered by asterisk. I think that asterisk cannot identify the destination DDI of the incoming call...is this normal? This is the capi debug of one incoming call: asterisk1*CLI> CONNECT_IND ID=001 #0x1975 LEN=0045 Controller/PLCI/NCCI = 0x401 CIPValue = 0x10 CalledPartyNumber = <81>0 CallingPartyNumber = <00 83>XXXXXXXXX CalledPartySubaddress = default CallingPartySubaddress = default BC = <80 90 a3> LLC = default HLC = <91 81> AdditionalInfo BChannelinformation = default Keypadfacility = default Useruserdata = default Facilitydataarray = default -- CONNECT_IND (PLCI=0x401,DID=0,CID=XXXXXXXXX,CIP=0x10,CONTROLLER=0x1) > ISDN1#02: msn='*' DNID='0' MSN == ISDN1#02: setting format alaw - 0x8 (alaw) == ISDN1#02: Incoming call 'XXXXXXXXX' -> '0' INFO_IND ID=001 #0x1976 LEN=0017 Controller/PLCI/NCCI = 0x401 InfoNumber = 0x70 InfoElement = <81>0 INFO_RESP ID=001 #0x1976 LEN=0012 Controller/PLCI/NCCI = 0x401 -- ISDN1#02: info element CALLED PARTY NUMBER > ISDN1#02: INFO_IND DID digits not used in this state. INFO_IND ID=001 #0x1977 LEN=0015 Controller/PLCI/NCCI = 0x401 InfoNumber = 0xa1 InfoElement = default INFO_RESP ID=001 #0x1977 LEN=0012 Controller/PLCI/NCCI = 0x401 -- ISDN1#02: info element Sending Complete CONNECT_RESP ID=001 #0x1977 LEN=0032 Controller/PLCI/NCCI = 0x401 Reject = 0x1 BProtocol B1protocol = 0x0 B2protocol = 0x0 B3protocol = 0x0 B1configuration = default B2configuration = default B3configuration = default ConnectedNumber = default ConnectedSubaddress = default LLC = default AdditionalInfo BChannelinformation = default Keypadfacility = default Useruserdata = default Facilitydataarray = default INFO_IND ID=001 #0x1978 LEN=0016 Controller/PLCI/NCCI = 0x401 InfoNumber = 0x18 InfoElement = <81> INFO_RESP ID=001 #0x1978 LEN=0012 Controller/PLCI/NCCI = 0x401 -- ISDN1#02: info element CHANNEL IDENTIFICATION 81 INFO_IND ID=001 #0x1979 LEN=0015 Controller/PLCI/NCCI = 0x401 InfoNumber = 0x8005 InfoElement = default INFO_RESP ID=001 #0x1979 LEN=0012 Controller/PLCI/NCCI = 0x401 -- ISDN1#02: info element SETUP > ISDN1#02: IE SETUP / SENDING-COMPLETE already received. DISCONNECT_IND ID=001 #0x197b LEN=0014 Controller/PLCI/NCCI = 0x401 Reason = 0x0 DISCONNECT_RESP ID=001 #0x197b LEN=0012 Controller/PLCI/NCCI = 0x401 -- ISDN1#02: DISCONNECT_IND on incoming without pbx, doing hangup. > CAPI/ISDN1/0-15: set channel task to 1 == ISDN1#02: CAPI Hangingup for PLCI=0x401 in state 4 == ISDN1#02: Interface cleanup PLCI=0x401 > CAPI devicestate requested for ISDN1/0 Anyone can give me ideas about this problem? Thanks in advance! Best regards, PS. _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users