I completely missed the 47-47. That wasn't very smart. With that T1, we don't have the full thing. We are sharing it with someone else, and 4 of the channels are used elsewhere. It was setup with em wink, so there isn't a d channel. I'm guessing I should have set both to 44 and it probably would have worked.
Do you think that could have caused my SPAN 1 error? Thanks, Rob David Gomillion wrote: > Tell us about channels 45-47... > > We have 45-47 defined in zapata.conf, but not in zaptel.conf. Probably > not the problem, but it might cause some confusion... > > Also, look at your timing sources. They don't look quite right to me. > Spans 1 and 2 are both marked as primary timing sources. > > Hope that helps, > David > > > On 1/4/07, *Rob Schall* <[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>> wrote: > > <Correction in my zapata.conf file I used> > > Hey Everyone, > > So this is a problem I've been having for sometime now. I sent a few > messages to the list with no luck. > > The problem is that when people dial into the Asterisk system > using DID > numbers, it works the first time or 2, then I get busy signals. > A friend recommended I clear out the zapata and zaptel, start > over, and > recreate my wanpipe stuff. He thought the problem was with the spans > themselves. > > However, when I use the following information, and restart > wanrouter, I > get an error. > > Zapata.conf > > [channels] > > language=en > context=internal > switchtype=national > pridialplan=unknown > signalling=pri_cpe > faxdetect=incoming > usecallerid=yes > echocancel=yes > echocancelwhenbridged=yes > group=0 > channel => 1-23 > > group=1 > signalling=em_w > channel => 25-47 > > > Zaptel.conf > > span=1,1,0,esf,b8zs > span=2,1,0,esf,b8zs > bchan=1-23 > dchan=24 > e&m=25-44 > > > > -------------ERROR---------------- > Channel map: > > Channel 01: Clear channel (Default) (Slaves: 01) > Channel 02: Clear channel (Default) (Slaves: 02) > Channel 03: Clear channel (Default) (Slaves: 03) > Channel 04: Clear channel (Default) (Slaves: 04) > Channel 05: Clear channel (Default) (Slaves: 05) > Channel 06: Clear channel (Default) (Slaves: 06) > Channel 07: Clear channel (Default) (Slaves: 07) > Channel 08: Clear channel (Default) (Slaves: 08) > Channel 09: Clear channel (Default) (Slaves: 09) > Channel 10: Clear channel (Default) (Slaves: 10) > Channel 11: Clear channel (Default) (Slaves: 11) > Channel 12: Clear channel (Default) (Slaves: 12) > Channel 13: Clear channel (Default) (Slaves: 13) > Channel 14: Clear channel (Default) (Slaves: 14) > Channel 15: Clear channel (Default) (Slaves: 15) > Channel 16: Clear channel (Default) (Slaves: 16) > Channel 17: Clear channel (Default) (Slaves: 17) > Channel 18: Clear channel (Default) (Slaves: 18) > Channel 19: Clear channel (Default) (Slaves: 19) > Channel 20: Clear channel (Default) (Slaves: 20) > Channel 21: Clear channel (Default) (Slaves: 21) > Channel 22: Clear channel (Default) (Slaves: 22) > Channel 23: Clear channel (Default) (Slaves: 23) > Channel 24: D-channel (Default) (Slaves: 24) > Channel 25: E & M (Default) (Slaves: 25) > Channel 26: E & M (Default) (Slaves: 26) > Channel 27: E & M (Default) (Slaves: 27) > Channel 28: E & M (Default) (Slaves: 28) > Channel 29: E & M (Default) (Slaves: 29) > Channel 30: E & M (Default) (Slaves: 30) > Channel 31: E & M (Default) (Slaves: 31) > Channel 32: E & M (Default) (Slaves: 32) > Channel 33: E & M (Default) (Slaves: 33) > Channel 34: E & M (Default) (Slaves: 34) > Channel 35: E & M (Default) (Slaves: 35) > Channel 36: E & M (Default) (Slaves: 36) > Channel 37: E & M (Default) (Slaves: 37) > Channel 38: E & M (Default) (Slaves: 38) > Channel 39: E & M (Default) (Slaves: 39) > Channel 40: E & M (Default) (Slaves: 40) > Channel 41: E & M (Default) (Slaves: 41) > Channel 42: E & M (Default) (Slaves: 42) > Channel 43: E & M (Default) (Slaves: 43) > Channel 44: E & M (Default) (Slaves: 44) > > 44 channels configured. > > ZT_SPANCONFIG failed on span 1: Invalid argument (22) > > > > > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > <http://lists.digium.com/mailman/listinfo/asterisk-users> > > > ------------------------------------------------------------------------ > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
