Hi,
I have made some headway with this. Let me explain a abit of the setup. I have an Orion GSM
Gateway, that was connected to a Cisco AS5300 via E1. When I looked at the AS5300 config, it was
talking R2 to the Orion. So I have tried to connect the Orion direclty to Asterisk (leaving out the
Cisco), using Unicall.
This is a problem I have with an incoming call, from Orion to Asterisk.
Jan 9 16:35:29 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/2 <- 0001 [1/
1/Idle /Idle ]
Jan 9 16:35:29 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2
UniCall/2 Detected
Jan 9 16:35:29 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/2 Making a new call
with CRN 32769
Jan 9 16:35:29 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/2 1101 -> [2/
2/Idle /Idle ]
Jan 9 16:35:29 WARNING[7262]: chan_unicall.c:2644 handle_uc_event: Unicall/2
event Detected
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/2 <- 1001 [2/
2/Seize ack /Seize ack ]
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/2 Far end
disconnected(cause=Normal, unspecified cause [31]) - state 0x2
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:2644 handle_uc_event: Unicall/2
event Far end disconnected
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:2930 handle_uc_event: CRN 32769 - far disconnected
cause=Normal, unspecified cause [31]
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2
UniCall/2 Call control(6)
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/2 Drop
call(cause=Normal Clearing [16])
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/2 Call
disconnected(cause=Normal, unspecified cause [31]) - state 0x800
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:2644 handle_uc_event: Unicall/2
event Drop call
Jan 9 16:35:31 DEBUG[7262]: chan_unicall.c:2978 handle_uc_event: CRN 32769 -
Doing a release call
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2
UniCall/2 Call control(7)
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2
UniCall/2 Release call
Jan 9 16:35:31 WARNING[7262]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/2 1001 -> [1/
1000/Clear fwd /Seize ack ]
The below output(in the mail) is of an outgoing call from Asterisk.
Can anyone please help me to see what is wrong?
yusuf wrote:
Hi,
if that means I should post my config, here goes:
zaptel:
span=1,1,3,cas,hdb3,crc4
cas=1-15:1101
cas=17-31:1101
unicall.conf:
protocolvariant=id,10,10
protocolend=cpe
group=1
channel => 1-15
channel => 17-31
wanpipe1.conf
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = CRC4
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
TE_HIGHIMPEDANCE = NO
LBO = 120OH
TE_SIG_MODE = CAS
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 9000
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 1
TDMV_DCHAN = 16
[w1g1]
ACTIVE_CH = ALL
TDMV_ECHO_OFF = NO
TDMV_HWEC = NO
Josué Conti wrote:
Hi Yusuf, how are you?
It orders in the list its configurations, so that let us can help.
Best Regards
Josue
2007/1/8, yusuf < [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>:
Hi all,
I have Asterisk 1.2.10, zaptel 1.2.7, spandsp-0.0.3pre22 compiled,
and a Sangoma A101, and when I
make a call I get this:
Jan 8 13:04:06 DEBUG[12252]: chan_unicall.c:2000 unicall_exception:
Exception on 19, channel 1
Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report:
MFC/R2 UniCall/1 <- 1101
[1/ 40/Seize /Idle ]
Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report:
MFC/R2 UniCall/1 0 on ->
[2/ 40/Group I /Idle ]
Jan 8 13:04:11 WARNING[12252]: chan_unicall.c:627 unicall_report:
MFC/R2 UniCall/1 R2 prot. err.
[2/ 40/Group I /DNIS ] cause 32769 - T1 timed out
Jan 8 13:04:11 WARNING[12252]: chan_unicall.c:627 unicall_report:
MFC/R2 UniCall/1 0 off ->
[1/ 1/Idle /Idle ]
Jan 8 13:04:11 WARNING[12252]: chan_unicall.c:627 unicall_report:
MFC/R2 UniCall/1 1001 ->
[1/ 1/Idle /Idle ]
Jan 8 13:04:11 WARNING[12252]: chan_unicall.c:2644 handle_uc_event:
Unicall/1 event Protocol failure
-- Unicall/1 protocol error. Cause 32769
Jan 8 13:04:11 WARNING[12252]: chan_unicall.c:627 unicall_report:
MFC/R2 UniCall/1 Channel echo cancel
Jan 8 13:04:11 DEBUG[12252]: chan_unicall.c:955 unicall_disable_ec:
disabled echo cancellation on
channel 1
Jan 8 13:04:11 WARNING[12250]: chan_unicall.c:627 unicall_report:
MFC/R2 UniCall/1 <- 1001
[1/ 1/Idle /Idle ]
Jan 8 13:04:11 WARNING[12250]: chan_unicall.c:627 unicall_report:
MFC/R2 UniCall/1 1001 ->
[1/ 1/Idle /Idle ]
-- Hungup 'UniCall/1-1'
What does "- Unicall/1 protocol error. Cause 32769" mean, and can
anyone help me.
--
--
thanks,
Yusuf
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
