Hi,
I checked by changing to from-zaptel, but no luck yet. Pls guide me on
this.
Regards,
vudura senadeera
------------------------------
>
> Message: 9
> Date: Fri, 19 Jan 2007 16:47:18 -0000
> From: "Robert Jenkins" < [EMAIL PROTECTED]>
> Subject: RE: [asterisk-users] Integrating asterisk with Toshiba
> Astrata DK380
> To: "'Asterisk Users Mailing List - Non-Commercial Discussion'"
> <[email protected]>
> Message-ID: <[EMAIL PROTECTED]>
> Content-Type: text/plain; charset="us-ascii"
>
> Hi,
>
> your zapata.con has 'context=from-pstn'
>
> Try changing this to 'context=from-zaptel'
>
> Robert Jenkins.
>
>
>
> _____
>
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] On Behalf Of Vidura
> Senadeera
> Sent: 19 January 2007 15:19
> To: [email protected]
> Cc: [EMAIL PROTECTED]
> Subject: [asterisk-users] Integrating asterisk with Toshiba Astrata
> DK380
>
>
>
> Deat all,
>
> I am in middle of integrate Asterisk with Toshiba astrata legacy pbx.
>
> Following is my setup
>
> Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX
>
> A =============================================> B
> C <============================================ D
>
> Asterisk PBX and strata PBX connected using back to back E1 cross cable.
> Physicall connectivity is OK. The digium TE110p
> LED state green. zttool also OK.
>
> Toshiba stata configured to make outbound call via E1 link with pressing
> 9
> and then the out side number.
>
> I was able to make call from soft phone to analog extension at toshiba
> pbx.
> A==> B way as shown above. But when trying to dial from
> Toshiba PBX analog extension to asterisk extension, by pressing 9 the
> call
> rejected.
>
> In the asterisk command prompt I'm having following error message.
>
> -- Extension '' in context 'from-pstn' from '' does not
> exist. Rejecting
> call on channel 0/31, span 1
>
> Is there any wrong in my setup. dial plan??, additional configuration if
> i
> required to put please guide me.
>
> I will be greately appreciated your feedback on this regard.
>
> configuration details
>
> /etc/zaptel.conf
> # Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0"
>
> span=1,1,0,ccs,hdb3,crc4
> bchan=1-15,17-31
> dchan=16
>
> /etc/asterisk/zapata.conf
>
> signalling=pri_net ; pri_cpe = PRI slave ; pri_net = PRI master
> switchtype=euroisdn
> ;switchtype=national
> echocancel=yes ; You can set this to 32, 64, or 128, tweak to your
> needs.
> echocancelwhenbridged=yes
> echotraining=400 ; Asterisk trains to the beginning of the call, number
> is
> in milliseconds
> callerid=asreceived
> overlapdial=no
> pridialplan=unknown
> immediate=no
> ;rxwink=300
> callprogress=no
> loadzone=au
> context=from-pstn ; Points to the default context of your
> extensions.conf
> group=2
> channel=>1-15
> channel=>17-31 ;PRI/E1 link
>
>
> [trunkgroups]
> trunkgroup=>2,16
> spanmap=1,2,1
>
>
>
> /etc/asterisk/extension.conf
>
> [from-zaptel]
> exten => _X.,1,Set(DID=${EXTEN})
> exten => _X.,n,Goto(s,1)
> exten => s,1,NoOp(Entering from-zaptel with DID == ${DID})
> ; If ($did == "") { $did = "s"; }
> exten => s,n,Set(DID=${IF($["${DID}"= ""]?s:${DID})})
> exten => s,n,NoOp(DID is now ${DID})
> exten => s,n,GotoIf($["${CHANNEL:0:3}"="Zap"]?zapok:notzap)
> exten => s,n(notzap),Goto(ext-did,${DID},1)
> ; If there's no ext-did,s,1, that means there's not a no did/no cid
> route.
> Hangup.
> exten => s,n,Macro(hangup)
> exten => s,n(zapok),NoOp(Is a Zaptel Channel)
> exten => s,n,Set(CHAN=${CHANNEL:4})
> exten => s,n,Set(CHAN=${CUT(CHAN,-,1)})
> exten => s,n,Macro(from-zaptel-${CHAN},${DID},1)
> ; If nothing there, then treat it as a DID
> exten => s,n,NoOp(Returned from Macro from-zaptel-${CHAN})
> exten => s,n,Goto(ext-did,${DID},1)
>
>
>
>
> --
> Thanks & Regards,
> Vidura B. Senadeera.
>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL:
>
http://lists.digium.com/pipermail/asterisk-users/attachments/20070119/0dd5e0be/attachment-0001.htm
>
> ------------------------------
>
> Message: 10
> Date: Fri, 19 Jan 2007 11:46:57 -0500
> From: "Chris Earle \(CBL\)" < [EMAIL PROTECTED]>
> Subject: [asterisk-users] Disconnect Supervision UK / BT solution?
> To: <[email protected] >
> Message-ID: <[EMAIL PROTECTED]>
> Content-Type: text/plain; charset="iso-8859-1"
>
> Hi all
>
> I'm using sangoma a200 cards in the UK and have the ongoing, often noted
>
> problem of disconnect supervision with BT POTS lines.
>
> Just noticed this post on
> http://www.voip-info.org/wiki/view/UK+Asterisk+Details
> stating that potentially someone's got a solution :
>
> "TDM400P & Not Detecting Hangups:
>
> Got a TDM400P installed and having problems with Asterisk not detecting
> hangups? Using BT? If so, contact BT and ask what the "Disconnect Clear
> Time" setting is for your phone line. Odds are it's probably 100.
> Increasing
> it to 800 fixed the issue for me.
>
> "Disconnect Clear Time" is BT's name for CPC. "
>
>
> Does anyone have any thoughts/confirmation about this finally being a
> viable
> solution? This disconnect supervision problem has plagued TDM and
> Sangoma
> cards for a long time!
>
> Comments appreciated before I get on the phone with BT
>
>
> --
> Chris Earle
> System Solutions Specialist
>
>
