BAD News! the card doesn't seem to work at all. even when it's detected by
kernel it doesn't send/recv any interrupts in system. /proc/interrupts shows
this.
i also send p to sysrq but nothing special was shown:
Zapata Telephony Interface Registered on major 196
Zaptel Version: SVN-branch-1.2-r1686M Echo Canceller: KB1
ACPI: PCI interrupt 0000:03:01.0[A] -> GSI 48 (level, low) -> IRQ 82
PCI Config reg is 02900117
WCTDM2400P: New Reg: fe590000!
Detected REG0: 00000100
Detected REG1: 00007849
Detected REG2: 0000001d
(pre) Reg fc is 50000027
(post) Reg fc is 50000024
Detected REG2: 0000ffff
wctdm2400p: reg is a04c0004
Resetting the modules...
On 2/18/07, Tzafrir Cohen <[EMAIL PROTECTED]> wrote:
On Sat, Feb 17, 2007 at 11:52:32PM +0330, Paradise Dove wrote:
> On 2/17/07, Tzafrir Cohen <[EMAIL PROTECTED]> wrote:
> >
> >On Sat, Feb 17, 2007 at 07:52:25PM +0330, Paradise Dove wrote:
> >> Hi,
> >>
> >> I'm running FC3 with kernel 2.6.11.
> >> All the binary files and zaptel kernel modules is not available to
system at
> >> boot time.
> >> They are extracted in a ram disk at system startup and then zaptel
modules
> >> are loaded manually and so on.
> >> I have no problem with this boot routine and i've been tested all
digium
> >> cards (expect tdm24) and they work fine till now.
> >>
> >> The problem appeared when i purchased the new TDM2400 card. after
installing
> >> this new card system stopped on modprobe wctdm24xxp ot boot time!
(randomly
> >> sleeping on "Resetting the modules.." / "During Resetting the
modules..."
> >> and sometimes "After resetting the modules...) but no step further.
> >> Nothing happened till i killed modprobe manually so no modules
detected on
> >> tdm24. (Port 1: Not Installed, ....)
Strange. You can kill the modprobe process? In't probing done in kernel
with the process in state D?
To see what the kernel is doing: alt-sysrq-p (or: echo p
>/proc/sysrq-trigger )
> >> My motherboard is a brand new Intel 3010 chipset from supermicro with
> >> 3.3Vpci slots. i also changed the motherboard to Intel 7230 chipset
> >> with 5V slot
> >> but nothing changed. I also switched back to zaptel-1.2.13 and
removed the
> >> modules from the board and re-inserted them as digium support
recommended,
> >> but nothing changed. I also changed to 2.6.12 kernel but still the
same
> >> problem.
> >>
> >> Finally i changed the system startup routine and copied all extracted
zaptel
> >> files to hard-disk into the standard location in kernel dirs and
found that
> >> now system starts-up with no problem and detects TDM24 at boot
time!!!
> >
> >Hmmm...
> >
> >How exactly do you load the modules? With insmod or modprobe?
>
>
> when i put zaptel modules in kernel dirs. it detects all the needed
modules.
> and from the dmesg it seems (as it should be) to load zaptel first and
then
> wctdm24xxp. so i don't need to do a insmod or modprobe at all. the
problem
> comes when i rmmod these modules and modprobe or insmod them again.
This is run somewhere in rc.sysinit . Specifically, where it loads
modules of "other" devices.
>
> >
> >> it seemed that the problem is that the wctdm24xxp needs to be
detected
> >at
> >> boot time by the kernel.
> >> But now the problem is that when i rmmod the wctdm24xxp module and
> >modprobe
> >> it again still system doesn't detect it and sleeps on modprobe utill
i
> >kill
> >> it.
> >>
> >> i dont have such a problem with all other cards from digium.
> >> i think this is a weird problem with wctdm24xxp driver.
> >
> >Another theory: only the first modprobe after a boot is successful, and
> >the modules are loaded automatically at boot.
>
>
> no it's not true that the first modprobe is the successful one. it
seems
> the card works when kernel detects it and loads the modules itself.
> something that happens before init scripts.
>
> Test: remove the modules copletely, reboot, re-add the modules and
> >modprobe again.
>
>
> you mean remove the physical modules? if yes i've done it once. made no
> sense
Yes. A long-shot, but easy to accomploish (if you can afford a reboot).
--
Tzafrir Cohen
icq#16849755 jabber:[EMAIL PROTECTED]
+972-50-7952406 mailto:[EMAIL PROTECTED]
http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
