I have a TELUS PRI for a while, resold via Bell... dropped it after a
few months due to broken promises and failure to deliver /any/ of the
things we said we required when ordering.
During this time, I learned that with a TELUS PRI you cannot send name.
It's simply dropped at the switch. If you want a name to show up, you
have to beg and plead for them to manually update a database of theirs.
On top of this, that name will show up on *all* DIDs associated with
your block, so you will have to either have no name, a generic name of
sorts, or buy individual phone numbers at a higher rate and beg them
each time to manually do the update.
If you find another way, please do share... but that is 6 months
headache we had just to find out that it was impossible to send the
name, despite the majority of their technicians stating otherwise.
This is in BC. Maybe it's different in Alta?
Webster, Andrew wrote:
Outbound calls on my Telus PRI aren't taking the Name portion of the
callerID. I've looked at the logs, and it is being set (see below),
but the PRI debug output doesn't show the name being sent anywhere. As
a result, received calls always display from Unknown (or just the number).
Is there some config that I've missed somewhere?
I'm running NI-1 (Telus says NI-2 doesn't support the name feature, so
they've changed my link type).
Version: Asterisk 1.2.14 svn rev 48468
Asterisk Log:
Executing Set("SIP/304-091aafb8", "CALLERID(all)=Andrew<nnnnnnnnnn>")
in new stack
(I've replaced the digits with n).
PRI debug shows:
> Protocol Discriminator: Q.931 (8) len=42
> Call Ref: len= 2 (reference 4/0x4) (Originator)
> Message type: SETUP (5)
> [04 03 80 90 a2]
> Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer
capability: Speech (0)
> Ext: 1 Trans mode/rate: 64kbps, circuit-mode (16)
> Ext: 1 User information layer 1: u-Law (34)
> [18 03 a9 83 81]
> Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive
Dchan: 0
> ChanSel: Reserved
> Ext: 1 Coding: 0 Number Specified Channel Type: 3
> Ext: 1 Channel: 1 ]
> [6c 0c 21 80 nn nn nn nn nn nn nn nn nn nn]
> Calling Number (len=14) [ Ext: 0 TON: National Number (2) NPI:
ISDN/Telephony Numbering Plan (E.164/E.163) (1)
> Presentation: Presentation permitted, user number not screened (0)
'nnnnnnnnnn' ]
>From zapata.conf:
callerid=asreceived
;Sangoma A101 port 1 [slot:12 bus:0 span: 1]
switchtype=ni1
context=from-zaptel
overlapdial=yes
facilityenable=yes
group=0
signalling=pri_cpe
channel => 1-23
Thanks!
--
Andrew
------------------------------------------------------------------------
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
