I think you are mixing something here. The FritzCard is not a "B1", so you don't need the b1 modules, the firmware and the /etc/capi.conf.
You can either use the FritzCard driver (binary modules from AVM), or you use mISDN (which is also already loaded according to your lsmod). When using mISDN, you can either use the mISDN-CAPI to really provide a CAPI interface, or just don't use CAPI and use chan_misdn instead. Armin On Wed, 7 Mar 2007, Giedrius Augys wrote: > Hello, > I have problem with capi, I can't install it. I have putted all info what I > did and what I get :). I think you can suggest me how to solve this > problem.and thanking you in anticipation. I have ISDN Frtiz!Card PCI > v2.1and I want to install it to my ubuntu box (kernel: > 2.6.17-10-server). Using command "lspci -vv" , I can see that kernel finds > this card: > *02:0d.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH > Fritz!PCI v2.0 ISDN (rev 02) > Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH Fritz!PCI > v2.0 ISDN > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Interrupt: pin A routed to IRQ 201 > Region 0: Memory at ff9fec00 (32-bit, non-prefetchable) [size=32] > Region 1: I/O ports at df80 [size=32] > Capabilities: [40] Power Management version 2 > Flags: PMEClk- DSI- D1- D2+ AuxCurrent=55mA > PME(D0-,D1-,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME-* > > > > I found tutorial in http://www.asteriskguru.com/tutorials/avm_b1.html .I > have installed these packages: > *ii capiutils 3.9.20060704-1 Utilities for > CAPI-capable ISDN cards > ii libcapi20-3 3.9.20060704-1 libraries for > CAPI support > ii libcapi20-dev 3.9.20060704-1 libraries for > CAPI support > ii avm-fritz-firmware-2.6.17-10 3.11+2.6.17.7-10.1 Firmware for AVM > Fritz! ISDN hardware* > > and downloaded firmaware from * > ftp://ftp.in-berlin.de/pub/capi4linux/firmware/b1/ .*My capi.conf is: > *b1pci /usr/share/isdn/b1.t4 DSS1 - - > - - P2P* > > Then I exec command capiinit start, I have noting on output, but it load > modules: > [EMAIL PROTECTED]:~# lsmod > Module Size Used by > b1pci 10624 0 > b1dma 17412 1 b1pci > b1 25856 2 b1pci,b1dma > capi 19392 0 > kernelcapi 49664 4 b1pci,b1dma,b1,capi > capifs 7176 2 capi > ipv6 271136 12 > lp 12964 0 > mISDN_l2 44288 0 > mISDN_l1 13192 0 > avmfritz 25740 0 > mISDN_isac 17280 1 avmfritz > mISDN_core 75648 4 mISDN_l2,mISDN_l1,avmfritz,mISDN_isac* > > But when I execute command cappinfo, I get : > [EMAIL PROTECTED]:~# capiinfo > capi not installed - No such device or address (6). > * > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
