A little with skinny debug set to on shows during register:
Device SEP00175A872053 is attempting to register
Requesting capabilities
Buttontemplate requested
Adding button: 9, 1
Sending 30006 template to cisco
Received SoftKey Template Request
Received SoftKeySetReq
RECEIVED UNKNOWN MESSAGE TYPE: c
Received CapabilitiesRes
Adding codec capability '0 (25)'
Adding codec capability '4 (4)'
Adding codec capability '8 (2)'
Adding codec capability '0 (15)'
Adding codec capability '0 (16)'
Adding codec capability '0 (11)'
Adding codec capability '256 (12)'
Adding codec capability '256 (12)'
Adding codec capability '0 (257)'
Device capability set to '268'
RECEIVED UNKNOWN MESSAGE TYPE: 49
RECEIVED UNKNOWN MESSAGE TYPE: 49
RECEIVED UNKNOWN MESSAGE TYPE: 4a
RECEIVED UNKNOWN MESSAGE TYPE: 9
Received Time/Date Request
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S
: Invalid SCCP message! : ID :92
It also show this message when going offhook:
RECEIVED UNKNOWN MESSAGE TYPE: 49
Setting ringer mode to '1'.
skinny_new: tmp->nativeformats=268 fmt=4
Attempting to Clear display on Skinny [EMAIL PROTECTED]
Clearing Display
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S
: Invalid SCCP message! : ID :85
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S
: Invalid SCCP message! : ID :11
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S
: Invalid SCCP message! : ID :9a
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S
: Invalid SCCP message! : ID :82
Looks to me that chan_skinny doesn't understand many important messages.
Any previous 7970G SCCP firmware that might work?
cheers
rick
Richard Klingler schrieb:
Sorry bringing it up again....
Meanwhile switched to asterisk 1.4.3 on fbsd-6.2 but still
no luck getting my 7970G to run via skinny...
It registers fine with *:
Adding button: 9, 1
Device capability set to '268'
asterisk*CLI> skinny show devices
Name DeviceId IP Type R NL
-------------------- ---------------- --------------- --------------- - --
cisco SEP00175A872053 xx.xx.xxx.xx 7970 Y 1
But on the phone I just see displayed the time and date but no
linelabel...
My skinny.conf is:
[general]
bindaddr=xx.xx.xxx.xx ; Address to bind to
bindport=2000 ; Port to bind to, default tcp/2000
dateformat=D.M.Y ; M,D,Y in any order (5 chars max)
keepalive=30
disallow=all
allow=all ; see doc/rtp-packetization for framing options
[cisco]
device=SEP00175A872053
model=7970
nat=1
callerid="Richard Klingler" <995>
mailbox=995
callwaiting=yes
transfer=yes
threewaycalling=yes
context=klingler
linelabel="phonelab"
line => 995
any ideas left?
Using now "cmterm-7970_7971-sccp.8-2-2SR1"
cheers
rick
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
.
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
