Hi List,
Just a simple question for the list this time..
I need to setup 2 Phones than can Both ring when an incoming
call is made to a certain number...
I have done this 3,000,000s times with CCM and have no
problems with it, But it is the 1st time I have needed to do
this with Asterisk.
I think it can be done using Queues/Agents but I'm just unsure
how do it..
The setup in question is a very small 5 Phones System based
on SME 7.1 & SAIL (Asterisk & web interface) I have a small
Sandbox setup here with me to test the test before I need to go
set it up on the live system. My test phone is a Grandstream
GXP 2000 but I will be using SPA-941's in the Live Environment
Any help with this simple question would be great.
Best Regards
Gavin Spurgeon
Systems Administrator
Leigh City Technology College
[EMAIL PROTECTED]
http://www.leighctc.kent.sch.uk
Tel: 01322 620501
Fax: 01322 620599
IS HelpDesk : Ext 541
----- Original Message -----
From: "Alexandre VERNIOL" <[EMAIL PROTECTED]>
To: "Asterisk Users Mailing List - Non-Commercial Discussion"
<[email protected]>
Sent: Friday, May 11, 2007 2:43 PM
Subject: Re: [asterisk-users] TDM410P
Great !!!
Thanks a lot !!
Nitesh Divecha a écrit :
Hello,
Here is my config: -
/etc/zaptel.conf
============
# T1 Configuration
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
span=2,1,0,esf,b8zs
bchan=25-47
dchan=48
span=3,1,0,esf,b8zs
bchan=49-71
dchan=72
span=4,1,0,esf,b8zs
bchan=73-95
dchan=96
/etc/asterisk/zapata-channels.conf <<You need to #include
zapata-channels.conf in your zapata.conf>>
========================
; signalling = pri_cpe is USER
; signalling = pri_net is NETWORK
group = 1
switchtype = national
signalling = pri_net
context = from-zaptel
channel => 1-23
group = 2
switchtype = national
signalling = pri_net
context = from-zaptel
channel => 25-47
group = 3
switchtype = national
signalling = pri_net
context = from-zaptel
channel => 49-71
group = 4
switchtype = national
signalling = pri_cpe
context = from-zaptel
channel => 73-95
I use FreePBX as my front-end to route calls... so I just assign the
trunk groups which I want to use...
Regards,
Nitesh
Alexandre VERNIOL wrote:
HI all,
Does some one can give me his configuration (zapta.conf, zaptel.conf,
sample for extensions.conf) for TDM410P card or similar (1/2/3/4 BRI
card)
Thanks in advance.
Cheers,
Alex
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
This message has been scanned for viruses and
dangerous content by the Systems @ the LeighCTC,
and is believed to be clean.
--
This message has been scanned for viruses and
dangerous content by the Systems @ the LeighCTC,
and is believed to be clean.
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
