Hello, I am from Mongolia and when I use telephone set with callerid it display callerid.
Yes, our phone company charge for callerid service. Balgaa ----- Original Message ----- From: "Steve Murphy" <[EMAIL PROTECTED]> To: "Balgansuren Batsukh" <[EMAIL PROTECTED]>; "Asterisk Users Mailing List - Non-Commercial Discussion" <[email protected]> Sent: Thursday, August 09, 2007 2:40 AM Subject: Re: [asterisk-users] FSK callerid On Wed, 2007-08-08 at 23:55 +0900, Balgansuren Batsukh wrote: > Hello, > > I installed Asterisk on Dell Precision workstation and configured with > sample configuration. > > I have two TDM400 board and one with 4xFXO and second one 4xFXS module > installed. > > I made call to telephone line connected to FXO port and never seen > callerid > on those lines. > > I tested cidsignalling and cidstart types and all doesn't work. Balgaa-- What country are you in? The CID conventions vary considerably from country to country! Your tonezone indicate US/France... Here in the US, the defaults in zapata.conf work fine for me: usecallerid=yes ;cidsignalling=bell ;cidstart=ring Are you sure your lines from the CO are providing CID? Out here where I'm at, the phone company charges extra for the privilege of CID. murf > > /var/log/messages: > ============ > Aug 3 13:42:51 towerpbx kernel: Module 0: Installed -- AUTO FXO (FCC > mode) > Aug 3 13:42:51 towerpbx kernel: Module 1: Installed -- AUTO FXO (FCC > mode) > Aug 3 13:42:51 towerpbx kernel: Module 2: Installed -- AUTO FXO (FCC > mode) > Aug 3 13:42:51 towerpbx kernel: Module 3: Installed -- AUTO FXO (FCC > mode) > Aug 3 13:42:51 towerpbx kernel: input: ImPS/2 Logitech Wheel Mouse as > /class/input/input2 > Aug 3 13:42:51 towerpbx kernel: Found a Wildcard TDM: Wildcard TDM400P > REV > I (4 modules) > Aug 3 13:42:51 towerpbx kernel: ACPI: PCI Interrupt 0000:02:08.0[A] -> > GSI > 17 (level, low) -> IRQ 185 > Aug 3 13:42:51 towerpbx kernel: Freshmaker version: 71 > Aug 3 13:42:51 towerpbx kernel: Freshmaker passed register test > Aug 3 13:42:51 towerpbx kernel: Module 0: Installed -- AUTO FXS/DPO > Aug 3 13:42:51 towerpbx kernel: Module 1: Installed -- AUTO FXS/DPO > Aug 3 13:42:51 towerpbx kernel: Module 2: Installed -- AUTO FXS/DPO > Aug 3 13:42:51 towerpbx kernel: Module 3: Installed -- AUTO FXS/DPO > Aug 3 13:42:51 towerpbx kernel: Found a Wildcard TDM: Wildcard TDM400P > REV > E/F (4 modules) > Aug 3 13:42:51 towerpbx kernel: ACPI: PCI Interrupt 0000:02:09.0[A] -> > GSI > 18 (level, low) -> IRQ 177 > Aug 3 13:42:51 towerpbx kernel: FALC version: 00000005 > Aug 3 13:42:51 towerpbx kernel: TE110P: Setting up global serial > parameters > for T1 FALC V2.2 > Aug 3 13:42:51 towerpbx kernel: TE110P: Successfully initialized serial > bus > for card > Aug 3 13:42:51 towerpbx kernel: Found a Wildcard: Digium Wildcard TE110P > T1/E1 > Aug 3 13:42:51 towerpbx kernel: Registered tone zone 0 (United States / > North America) > Aug 3 13:42:51 towerpbx kernel: Registered tone zone 2 (France) > Aug 3 13:42:51 towerpbx kernel: Registered tone zone 0 (United States / > North America) > Aug 3 13:42:51 towerpbx kernel: Registered tone zone 2 (France) > > zapata.conf > ======== > usecallerid=yes > callerid=asreceived > cidsignalling=dtmf > cidstart=ring > sendcalleridafter=1 > > Is there any to support FSK callerid? > > How can I to debug callerid detection process on asterisk? > > Regards, > Balgaa > > > _______________________________________________ > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
