Hi, sorry but perhaps I don't have explained clearly my problem...now I have a box voip that must be replace with another box voip but I want to do test before remove the old voip from production.
The box voip (named 1) that now is in production have three card, two isdn card and TDM2400P that I want remove for to install in the new box voip (named 2). On the box voip 1 I have: Asterisk version 1.2.13 The kernel version is: 2.6.19.2 ..but on the box voip 2 I have the new asterisk version and kernel. On box voip 1 I have: zaptel.conf: loadzone=it defaultzone=it span=2,1,3,ccs,ami bchan=25-26 dchan=27 span=3,1,3,ccs,ami bchan=28-29 dchan=30 fxsls=1-24 ..in zapata.conf I have: [channels] language=it ... ... ;Linee ISDN immediate=no switchtype=euroisdn signalling = bri_net priindication=outofband group = 1 channel => 25-26 group = 2 channel => 28-29 ;Linee tdm immediate=yes .. .. cidstart=ring signalling=fxs_ls group = 3 channel => 1-5 ..and always on box voip 1: [EMAIL PROTECTED]:~# lsmod Module Size Used by zaphfc 16796 6 wctdm24xxp 63552 5 zaptel 192132 26 zaphfc,wctdm24xxp ..in /etc/rc.d/rc.modules: rc.modules rc.modules-2.4.33.3 ..my problem is how remove TDM Card from voip box 1 without stop this box voip, if I remove in correctly mode the TDM Card I can configure this card on new voip box 2 and to do test before of put new box voip in production in replacement the box voip 1. The stesp that I think correctly for remove TDM Card: - remove line configuration about tdm card in zapata.conf and zaptel.conf - remove in rc.modules and rc.modules-2.4.33.3 line: /sbin/modprobe wctdm24xxp && /sbin/ztcfg -vvvvvv - rmmod wctdm24xxp - halt - remove physically card tdm from pc (box voip 1) - restart box voip 1 ..this procedure is ok ? Thanks ! ------ Salvatore. ----- Original Message ----- From: "Jon Pounder" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Wednesday, November 28, 2007 3:53 PM Subject: Re: [asterisk-users] Fw: Remove a TDM Card > Quoting Tony Plack <[EMAIL PROTECTED]>: > >> >>> Hi, sorry for my insistence but this is a big problem for me..my >>> steps for remove card are ok ? Thanks. > > > its not much help but I have found in general asterisk is not too > graceful about zap numbering and even starting when the cards in place > don't match the configuration. > > yeah the config is wrong but sometimes there are legitimate reasons > for that like taking a card out for 5min to try something you should > be able to still boot the remaining system without it, or add the > configs before putting the card in. Bigger issue is getting around the > renumbering of channels when you remove hardware at the "bottom" > > > >>> >>> ------ >>> >>> Salvatore. >>> >>> ----- Original Message ----- >>> From: "Sasa" <[EMAIL PROTECTED]> >>> To: <[email protected]> >>> Sent: Monday, November 26, 2007 4:25 PM >>> Subject: [asterisk-users] Remove a TDM Card >>> >>> >>>> Hi, I would like remove a Digium TDM2400P from Asterisk (version >>>> 1.2.13) box >>>> but when I remove card from the PC after reboot Asterisk not >>>> started correctly. On box now with TDM Card I have: >>>> >>>> [EMAIL PROTECTED]:~# lsmod >>>> Module Size Used by zaphfc >>>> 16796 6 wctdm24xxp 63552 >>>> 5 >>>> zaptel 192132 26 >>>> zaphfc,wctdm24xxp >>>> >>>> The kernel version is: >>>> 2.6.19.2 >>>> >>>> ..then I have in /etc/rc.d/rc.modules: >>>> rc.modules >>>> rc.modules-2.4.33.3 >>>> >>>> ..both files are identical: >>>> >>>> #!/bin/sh >>>> /sbin/modprobe zaptel >>>> /sbin/modprobe zaphfc modes=3 && /sbin/ztcfg -vvvvvv >>>> /sbin/modprobe wctdm24xxp && /sbin/ztcfg -vvvvvv >>>> >>>> ..in zapata.conf I have: >>>> >>>> signalling=fxs_ls >>>> group = 3 >>>> channel => 1-5 >>>> >>>> ..and in zaptel.conf I have: >>>> fxsls=1-24 >>>> >>>> ..now my dobious is about correct steps for remove TDM Card from >>>> PC, I think that: >>>> >>>> - remove line configuration in zapata.conf and zaptel.conf - >>>> remove in rc.modules and rc.modules-2.4.33.3 line: >>>> /sbin/modprobe wctdm24xxp && /sbin/ztcfg -vvvvvv - rmmod >>>> wctdm24xxp - reboot >>>> >>>> ..this procedure is ok ? >>>> Thanks. >>>> >>>> ------ >>>> >>>> Salvatore. >>>> >> >> 1.2.13 has some exploits and you should consider running something >> newer. 1.2 branch has no official support. >> >> However... >> >> You should make sure to load ztdummy in place of your tdm card. If >> I remember correctly 1.2 requires a timing source. >> modules-2.4.33.3 is for an old kernel and shouldn't apply to the >> current 2.6.19.2. >> >> Normally the TDM card provides this 1000Hz timing source when >> available, but ztdummy can mimic this timing from the kernel clock >> source. >> >> ztdummy may (or may not) have issues with your kernel version as a >> timing source. I believe kernel 2.6.21 or better solved a few >> problems with clock sources. >> >> Other than that, your steps are fine. >> >> _______________________________________________ >> --Bandwidth and Colocation Provided by http://www.api-digital.com-- >> >> asterisk-users mailing list >> To UNSUBSCRIBE or update options visit: >> http://lists.digium.com/mailman/listinfo/asterisk-users >> > > > > Jon Pounder > > _/_/_/ _/ _/ _/ _/_/_/ _/ _/ _/_/_/_/ > _/ _/_/ _/ _/ _/ _/_/ _/ _/_/ > _/ _/ _/_/ _/ _/ _/ _/_/ _/ > _/_/_/ _/ _/ _/_/_/_/ _/_/_/ _/ _/ _/_/_/_/ > > > Inline Internet Systems Inc. > Thorold, Ontario, Canada > > Tools to Power Your e-Business Solutions > www.inline.net > www.ihtml.com > www.ihtmlmerchant.com > www.opayc.com > > ---------------------------------------------------------------- > This message was sent using IMP, the Internet Messaging Program. > > > > _______________________________________________ > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
