That's not going to tell you anything about the digits in transit. That's just telling you that your PRI is up. you are going to need exten => 4DIGITS
________________________________
From: [EMAIL PROTECTED] on behalf of broadband Voice
Sent: Sat 3/15/2008 1:34 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] DID T1 PRI
Additional output
[EMAIL PROTECTED] ~]# /sbin/ztcfg -vv
Zaptel Version: 1.4.9
Echo Canceller: MG2
Configuration
======================
SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: Clear channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: D-channel (Default) (Slaves: 24)
24 channels to configure.
On 3/15/08, broadband Voice <[EMAIL PROTECTED]> wrote:
Can you share with me sample extensions.conf? This is what I have
exten => 215xxxxxxx,1,Dial(Zap/1)
in zapata.conf
[channels]
context=external
switchtype=ni1
resetinterval=3600
overlapdial=no
priindication=outofband
facilityenable=yes
signalling=pri_cpe
usecallerid=yes
cidsignalling=bell
hidecallerid=no
restrictcid=no
usecallingpres=yes
echocancel=yes
callerid=asreceived
faxdetect=incoming
nsf=sdn
group=1
channel=>1-23
zaptel.conf
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
On 3/15/08, Darren Wright <[EMAIL PROTECTED]> wrote:
Feel free to ping me off list. I've setup quite a few Cavtel
PRI's with *.the paperwork they asked you to setup?
Typically, they only send 4 digits.
Do you have the questionnare they asked you to fill out?
dwright at d2 - tech dot com.
________________________________
From: [EMAIL PROTECTED] on behalf of broadband Voice
Sent: Fri 3/14/2008 9:04 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] DID T1 PRI
Thanks. I am in Philly. I may have to configure the
extensions.conf well to pass the incoming channels.
On 3/14/08, Steve Totaro <[EMAIL PROTECTED]> wrote:
On Fri, Mar 14, 2008 at 8:13 PM, broadband Voice
<[EMAIL PROTECTED]> wrote:
> I had Cavalier turn up a T1 PRI. How can I put in the
DIDs to direct to
> Asterisk. Here is a log
>
>
>
> Zaptel Tool (C)2002 Linux Support Services, Inc.
> ââââââââââââââââ⤠T2XXP (PCI) Card 0 Span 1
> ââââââââââââââââââ[3;10Hâterfaces âââââââââââââââââ
âââââ[3;37Hâ
> â â
>
> â
â
> â
> â Current Alarms: No alarms.
â rd 0
> Span 1 â â
> â Sync Source: T2XXP (PCI) Card 0
Span 1 â rd
> 0 Span 2 â(R) â
> â IRQ Misses: 0
â
> â â
> â Bipolar Viol: 0
â
> â â
> â Tx/Rx Levels: 0/ 0
â
> â(R) â
> â Total/Conf/Act: 24/ 24/ 0
â
> â â
> â 111111111122222
ââââââââ â
> â â
> â 123456789012345678901234
â Back â â
> â â
> â TxA ------------------------
ââââââââ â
> â â
> â TxB ------------------------
â
> â â
> â TxC ------------------------
â
> â
> â TxD ------------------------
â
> â
> â
ââââââââ â14Câ
> â RxA ------------------------
â Loop â â
> â Quit â â
> â RxB ------------------------
ââââââââ â
> ââââââââ â
> â RxC ------------------------
â
> â
> â RxD ------------------------
â
> ââââââââââââââââââââââââââââââââââââââ
> â
â
>
ââââââââââââââââââââââââââââââââââââââââââââââââââââââââââââââ
>
> T2XXP (PCI) Card 0 Span 1
> F10=Back
>
>
> I need to add 215-xxx-xxxx etc to come in to the
Asterisk box.
>
>
Do you have DIDs already? When you call a DID and watch
the Asterisk
console with a little verbose, you should see the call
come and how
many digits the telco is sending.
Then you need to make matching entries for those DIDs
either in the
form of exact matches or pattern matches to do pretty
much whatever
you can imagine.
Are you in Philly?
Thanks,
Steve Totaro
_______________________________________________
-- Bandwidth and Colocation Provided by
http://www.api-digital.com <http://www.api-digital.com/>
<http://www.api-digital.com/> --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
This message was sent from D2 Technology, INC.
_______________________________________________
-- Bandwidth and Colocation Provided by
http://www.api-digital.com <http://www.api-digital.com/> --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
This message was sent from D2 Technology, INC.
<<winmail.dat>>
_______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
