Sasa, Sometimes I have to do a hard reset of the phone in order to get it to load the SIP firmware, even when the load file is specified in the SEP<MAC>.conf file.
Make sure that only the contents of the cop file and the SEP<mac>.cnf file are present in your tftp root. Then unplug the phone and press and hole the # key. Plug the phone back in, still holding the # key. When the line buttons begin turn on and off in sequence, press 123456789*0#. This will factory reset the phone and should cause it to check the termxx.default.loads file for the proper image. It will then read the SIP image name from that file and flash itself with the SIP image. Dave -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Sasa Sent: Thursday, October 09, 2008 8:51 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] Cisco 7906g & SIP Hi Dave, the cmterm-7911_7906-sip.8-0-4sr1.cop is a compressed file and on the inside has: apps11.1-1-3-15.sbn cnu11.3-1-3-15.sbn copstart.sh cvm11sip.8-0-3-16.sbn dsp11.1-1-3-15.sbn jar11sip.8-0-3-16.sbn load307 load369 SIP11.8-0-4SR1S.loads term06.default.loads term11.default.loads I use Cisco7941 without callmanager software but only with SIP support. Thanks. ------ Salvatore. ----- Original Message ----- From: "David Gibbons" <[EMAIL PROTECTED]> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Thursday, October 09, 2008 2:30 PM Subject: Re: [asterisk-users] Cisco 7906g & SIP > Sasa, > > You can actually just rename the .cop file to a .tar.gz file. Cisco > doesn't have (to my knowledge) any non-callmanager SIP software. The SIP > load is just a SIP load, not a SIP load unique to generic SIP or > callmanager. > > Dave > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of Stefan > Gofferje > Sent: Thursday, October 09, 2008 7:28 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [asterisk-users] Cisco 7906g & SIP > > Sasa schrieb: >>> I need other files other than those obtained with >>> cmterm-7911_7906-sip.8-0-4sr1.cop ?? > > cmterm is the callmanager software. You need to get the non-callmanager > SIP-software. Contact your local Cisco representative to buy a license > for that. > > Terve, > Stefan > > -- > Last words of a stormchaser: > "Where is that rotation on the radar?!" > > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users