Ok!! Do this finale test.
call fron analog lines to any number, wait until the called hang up. Now tell us the signal tone. If the signal is busy ? or any thing else.... Your set up look ok. Now try with this options into zapata.conf header: zapata.conf: usecallerid=yes hidecallerid=no callwaiting=no threewaycalling=yes transfer=yes echocancelwhenbridged=no immediate=no faxdetect=no busydetect=yes busycount=4 On Fri, Oct 10, 2008 at 11:42 AM, Gordon Henderson <[EMAIL PROTECTED]> wrote: > On Thu, 9 Oct 2008, Mike wrote: > >> Folks, >> >> I've seen a few reports that people have had problems with hang up >> detection on UK cable phone lines. I have a TDM400P with two FXO ports, >> one connected to my BT line and the other connected to my >> Telewest/Virgin Media cable line. If I ring the BT line and then clear >> down, Asterisk detects this and acts accordingly. If I ring the >> Telewest line, the clear down is not detected, hence Asterisk continues >> to ring extentions, record voicemail, etc. >> >> I've seen a few posts reporting this issue with the UK cable system but >> these are generally not resolved. >> >> Has anyone sucessfully configured a UK Telewest line with Astersik? >> Does anyone know how Telewest signals that the remote caller has cleared >> down? > > I did an instalaltion yesterday with 2 Teleworst lines. > > When I was calling in on my mobile, then hanging up, it seemed to work ok > - it did keep the line open for a few seconds, but I see that with BT too. > >> On the same topic, how does BT signal remote clear down? > > Dunno... > >> I have plugged a phone into the Telewest line and it doesn't appear to >> receive a tone on clear down, nor does it appear to drop power on the >> line. Just in case, I changed the DCT in zaptel.h from 500ms to 100ms and >> recompiled, however, this did not resolve the issue. > > I'm using asterisk 1.2.30, Zaptel 1.2.24. Oslec and an OpenVox card. > >> I'm working blind at the moment as I cannot find anything which >> documents what to expect the Telewest line to do to signal a remote >> clear down occured. I've played around with the kewlstart and >> loop-start setting but without knowing what the line is going to do, >> it's difficult to know how to configure Asterisk. >> >> Does anyone have any experience of Telewest? > > Only 2 sites and they both seem to work OK - One in Bristol the other in > Plymouth. > > Can't get caller ID to work though )-: > > Zaptel.conf: > > fxsks=3 > fxsks=4 > loadzone=uk > defaultzone=uk > > > zapata.conf: > > usecallerid=yes > cidsignalling=v23 > cidstart=polarity > hidecallerid=no > callwaiting=no > threewaycalling=yes > transfer=yes > echocancel=256 > ;echocancel=yes > ;echotraining=yes > echocancelwhenbridged=no > immediate=no > faxdetect=no > > > ; Channel 3: PSTN line > context=incoming > group=1 > usecallerid=no > faxdetect=none > signalling=fxs_ks > rxgain=4 > txgain=4 > callerid=asreceived > channel => 3 > > ; Channel 4: PSTN line > context=incoming > group=1 > usecallerid=no > faxdetect=none > signalling=fxs_ks > rxgain=4 > txgain=4 > callerid=asreceived > channel => 4 > > > Gordon > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > -- --------------------------------------------------------------------------------- Luis Morales Consultor de Tecnologia Cel: +(58)416-4242091 --------------------------------------------------------------------------------- "Empieza por hacer lo necesario, luego lo que es posible... y de pronto estarás haciendo lo imposible" Leonardo Da'Vinci --------------------------------------------------------------------------------- _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
