Have you done a sip set debug, then sip reload? Do you have a range of 10000-20000 open in your firewall? Asterisk will "poke out" through 5060 but has to get a random response back in the 10-20K range (you can narrow this)
-----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of obitori junk Sent: Friday, December 19, 2008 4:28 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] Problem configuring Asterisk as client for ekiga.net -- NAT problem I tried both "disallow all /// allow ulaw" and "allow all". Neither worked. Ekiga.net is not accepting asterisk as a client. I keep getting the "600 not acceptable error". What seems odd to me is that the NAT column shows an "n" for both ekiga.net and jnctn.net, but I have "nat=yes" for both. Thanks for the suggestion...I'm still open to ideas. Regards, Bud Roth sip.conf contains: "allow all" OUTPUT--> Name/username Host Dyn Nat ACL Port Status ekiga/budzhaus 86.64.162.35 N 5060 OK (102 ms) 110 (Unspecified) D 0 UNKNOWN 109 (Unspecified) D 0 UNKNOWN 108 (Unspecified) D 0 UNKNOWN 107 (Unspecified) D 0 UNKNOWN 106 (Unspecified) D 0 UNKNOWN 105 (Unspecified) D 0 UNKNOWN 104 (Unspecified) D 0 UNKNOWN 103 (Unspecified) D 0 UNKNOWN 102/102 10.1.1.20 D 5061 OK (1 ms) 101 (Unspecified) D 0 UNKNOWN jnctn/obitori 66.227.100.20 N 5060 OK (22 ms) 12 sip peers [Monitored: 3 online, 9 offline Unmonitored: 0 online, 0 offline] [Dec 19 17:20:31] NOTICE[2478]: chan_sip.c:7517 sip_reg_timeout: -- Registration for '[email protected]' timed out, trying again (Attempt #2) -- Got SIP response 606 "Not Acceptable" back from 86.64.162.35 sip.conf contains: disallow all allow ulaw OUTPUT--> victoria*CLI> sip show peers Name/username Host Dyn Nat ACL Port Status ekiga/budzhaus 86.64.162.35 N 5060 OK (97 ms) 110 (Unspecified) D 0 UNKNOWN 109 (Unspecified) D 0 UNKNOWN 108 (Unspecified) D 0 UNKNOWN 107 (Unspecified) D 0 UNKNOWN 106 (Unspecified) D 0 UNKNOWN 105 (Unspecified) D 0 UNKNOWN 104 (Unspecified) D 0 UNKNOWN 103 (Unspecified) D 0 UNKNOWN 102/102 10.1.1.20 D 5061 OK (1 ms) 101 (Unspecified) D 0 UNKNOWN jnctn/obitori 66.227.100.20 N 5060 OK (23 ms) 12 sip peers [Monitored: 3 online, 9 offline Unmonitored: 0 online, 0 offline] victoria*CLI> On Fri, 2008-12-19 at 15:18 -0600, Eric "ManxPower" Wieling wrote: > obitori junk wrote: > > I am experiencing a "606 not Acceptable" error trying to set up an > > Asterisk server as an ekiga.net client. My server is behind a firewall > > with NAT routing. I have googled this problem and read about Asterisk > > feeding its local ip address to ekiga.net. That seems to be my > > problem. > > In my experience "Not Acceptable" errors happen because the two > endpoints cannot agree on a codec. Try allowing all the codecs in your > softphone and in Asterisk sip.conf [general] do a disallow=all and an > allow=ulaw. I suggest you do this in [general] when testing because > it can sometimes be hard to make sure that a peer/friend/user entry is > actually matching the incoming call. Once you get it working you can > refine it. > > You could be having a NAT issue too, but I don't think it is related to > your 606 error. > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
