[r...@vicidialnow ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1 NAME="" BOOTPROTO=none TYPE=Ethernet DEVICE=eth1 MTU="" NETMASK=255.255.255.0 BROADCAST=192.168.0.100 IPADDR=192.168.0.100 NETWORK=192.168.0.0 ONBOOT=no
On Mon, Jan 26, 2009 at 4:07 PM, David @ULC <[email protected]> wrote: > lspci Returns me below Output :_________________________________ > > [r...@vicidialnow ~]# lspci > 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev > 03) > 00:02.0 VGA compatible controller: Intel Corporation 82G35 Express > Integrated Gr > aphics Controller (rev 03) > 00:02.1 Display controller: Intel Corporation 82G35 Express Integrated > Graphics > Controller (rev 03) > 00:19.0 Ethernet controller: Intel Corporation 82566DC Gigabit Network > Connectio > n (rev 02) > 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Contolle > r #4 (rev 02) > 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Controll > er #5 (rev 02) > 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI > Control > ler #2 (rev 02) > 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio > Controller > (rev 02) > 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port > 1 (r > ev 02) > 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port > 2 (r > ev 02) > 00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port > 3 (r > ev 02) > 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Controll > er #1 (rev 02) > 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Controll > er #2 (rev 02) > 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Controll > er #3 (rev 02) > 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI > Control > ler #1 (rev 02) > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2) > 00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface > Controll > er (rev 02) > 00:1f.2 IDE interface: Intel Corporation 82801H (ICH8 Family) 4 port SATA > IDE Co > ntroller (rev 02) > 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev > 02) > 00:1f.5 IDE interface: Intel Corporation 82801H (ICH8 Family) 2 port SATA > IDE Co > ntroller (rev 02) > 03:00.0 IDE interface: JMicron Technologies, Inc. JMB368 IDE controller > 04:03.0 Ethernet controller: D-Link System Inc DGE-530T Gigabit Ethernet > Adapter > (rev 11) (rev 11) > 04:05.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70) > > > > ifconfig -a Returns : > _________________________________ > > ifconfig -a > eth0 Link encap:Ethernet HWaddr 00:1E:58:A7:3D:73 > inet addr:121.247.xxx.xxx Bcast:121.247.xxx.xxx > Mask:255.255.255.0 > inet6 addr: fe80::21e:58ff:fea7:3d73/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:415 errors:0 dropped:0 overruns:0 frame:0 > TX packets:478 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:51514 (50.3 KiB) TX bytes:95169 (92.9 KiB) > Interrupt:169 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:112962 errors:0 dropped:0 overruns:0 frame:0 > TX packets:112962 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:9165137 (8.7 MiB) TX bytes:9165137 (8.7 MiB) > > sit0 Link encap:IPv6-in-IPv4 > NOARP MTU:1480 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > > > > > > > > > > > On Sun, Jan 25, 2009 at 2:53 PM, David @ULC <[email protected]> wrote: > >> *Quote:* >> >> >> [r...@vicidialnow src]# service network restart >> Shutting down interface eth0: [ OK ] >> Shutting down loopback interface: [ OK ] >> Bringing up loopback interface: [ OK ] >> Bringing up interface eth0: [ OK ] >> Bringing up interface eth1: skge device eth1 does not seem to be present, >> delaying initialization. >> [FAILED] >> [r...@vicidialnow src]# >> >> >> >> >> eth1 is the Oboard card. I did install driver but its same. I am sure >> Driver is a correct one as after installing driver it showed me the card >> which is eth1 but due to soem issues I deleted that network interface from >> webmin. >> >> But now its NOT detecting. >> >> Kindly advice >> ____________ >> > >
_______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
