Based on this link - http://www.trixbox.org/forums/vendor-forums-certified/sangoma/a101dx-hangup- cause-code-90-outbound-calls
I'd check my polarity settings in dahdi.conf. Maybe signaling? -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Kal Feher Sent: Tuesday, May 26, 2009 8:22 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] Unable to make outbound calls Sorry. I don't get many opportunities to test this system as its live. Here are the results: -- Executing [...@dlpn_dialplan1:1] Dial("SIP/19722-b650fb80", "DAHDI/1") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1 -- Channel 0/1, span 1 got hangup, cause 90 WARNING[6454]: app_dial.c:765 wait_for_answer: Unable to forward voice or dtmf -- Hungup 'DAHDI/1-1' == Everyone is busy/congested at this time (1:0/0/1) On 20/5/09 3:52 PM, "Danny Nicholas" <[email protected]> wrote: > This all looks ok. What happens if you try to access the DAHDI channel > outside of Asterisk control: > In dialplan > Exten => 9,1,Dial(DAHDI/1) > > Dial 9 > Get dialtone > Dial number > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Kal Feher > Sent: Wednesday, May 20, 2009 2:55 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [asterisk-users] Unable to make outbound calls > > I attached the show channels in my first post, but removed it to reduce the > length of replies. Here it is again along with show status. > Note that there is only 1 PRI currently attached. > > geriatrix*CLI> dahdi show status > Description Alarms IRQ bpviol > CRC4 > T2XXP (PCI) Card 0 Span 1 OK 0 0 0 > T2XXP (PCI) Card 0 Span 2 RED 0 0 0 > > geriatrix*CLI> dahdi show channels > Chan Extension Context Language MOH Interpret > pseudo default default > 1 DID_span_1 default > 2 DID_span_1 default > 3 DID_span_1 default > 4 DID_span_1 default > 5 DID_span_1 default > 6 DID_span_1 default > 7 DID_span_1 default > 8 DID_span_1 default > 9 DID_span_1 default > 10 DID_span_1 default > 11 DID_span_1 default > 12 DID_span_1 default > 13 DID_span_1 default > 14 DID_span_1 default > 15 DID_span_1 default > 16 DID_span_1 default > 17 DID_span_1 default > 18 DID_span_1 default > 19 DID_span_1 default > 20 DID_span_1 default > 21 DID_span_1 default > 22 DID_span_1 default > 23 DID_span_1 default > 25 DID_span_2 default > 26 DID_span_2 default > 27 DID_span_2 default > 28 DID_span_2 default > 29 DID_span_2 default > 30 DID_span_2 default > 31 DID_span_2 default > 32 DID_span_2 default > 33 DID_span_2 default > 34 DID_span_2 default > 35 DID_span_2 default > 36 DID_span_2 default > 37 DID_span_2 default > 38 DID_span_2 default > 39 DID_span_2 default > 40 DID_span_2 default > 41 DID_span_2 default > 42 DID_span_2 default > 43 DID_span_2 default > 44 DID_span_2 default > 45 DID_span_2 default > 46 DID_span_2 default > 47 DID_span_2 default > > > > On 19/5/09 6:31 PM, "Danny Nicholas" <[email protected]> wrote: > >> Please post your CLI output from dahdi show status and dahdi show > channels. >> >> -----Original Message----- >> From: [email protected] >> [mailto:[email protected]] On Behalf Of Kal Feher >> Sent: Tuesday, May 19, 2009 11:22 AM >> To: [email protected] >> Subject: Re: [asterisk-users] Unable to make outbound calls >> >> >>> Can you make an outbound call after your first incoming call? That's > what >> I >> experienced with 1.4.24. >> >> No I can't. I saw similar threads while searching for a solution, but in > my >> case outbound calls are never possible. >> >> >> Regardless, thank you for your suggestion. >> >> On 19/5/09 4:47 PM, "Kal Feher" <[email protected]> wrote: >> >>>> I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 >>>> >>>> I've got a 2 port T2XXP card attached with on T1 currently plugged in. >>>> >>>> Inbound calls work fine, but outbound fail with the rather cryptic: >>>> [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable >> to >>>> create channel of type 'DAHDI' (cause 0 - Unknown) >>>> >>>> There are similar threads I've found on the net but they tend to be >> related >> to >>>> dahdi not being loaded or similar. In my case dahdi is loaded and >> channels >>>> visible. >>>> >>>> I've rsync'd a configuration (/etc/asterisk and /etc/dahdi) from another >>>> server that is currently working fine. But still no luck. >>>> >>>> Any hints would be appreciated. In particular if someone can suggest > some >>>> documentation on what _could_ cause a (cause 0 - Unknown) then I can >>>> investigate those. >>>> >>>> Some details below: >>>> <removed in reply to keep email readable> >> -- Kal _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
