Hello all, I have a new Carrier Access Adit 600 and am having a problem dialing out and receiving incoming calls.
After the initial ring, the calling party will here nothing. There is a silence, but the SIP phones that is supposed to ring will ring. The calling party will not hear the sound of the ring that * sends out on the line. Additionally, if someone picks up the receiver there is no sound, but occasionally you can here something trying to get through that sounds like tin-foil is over the MIC of the phone. The Channel bank is grounded properly, and only has one 8 Port FXO card. Also, there is nothing in any of the PCI slots except the 1 T100P card. Sometimes calls will work great (it's very sporadic), and everything sounds really clear. Sometimes there will be no sound on the line, others when trying to place an outgoing call the dialtone will sound like it has a lot of static I have six phone lines from Verizon and the problem will occur on all of the phone lines, not just one. I have trouble-shooted this thing extensively and have hit a wall. I have attached my configurations (zaptel.conf, zapata.conf, and print config (from the CB)). Has anyone seen anything like this before? Any help or other avenues to try to trouble shoot would be greatly appreciated! Thanks, B ---/etc/zaptel.conf--- span=1,1,0,esf,b8zs fxsks=1-6 # BMZ has the option to add more cards / lines to the CB # Setup T1 Span 2 # span=2,1,0,esf,b8zs # fxoks=25-48 loadzone = us defaultzone=us ---/etc/asterisk/zapata.conf---- [channels] language=en ; Set the context for dialplan calling group=1 context=incoming ; FXO Cards use FXS signalling, lets use Kickstart signalling=fxs_ks ; Cancel that Echo echocancel = yes echocancelwhenbridged = yes busydetect=no callprogress=no channel => 1-6 ---ADIT CB 600 print config---- > print config ------------------------------------------------------------- -Adit 600 configuration file -Created on 01/02/2002 at 07:13:02 -This file is valid for the following configuration only: - - CardType - -------- -SLOT A T1x2 SW Version: 6.1.2 -SLOT 1 FXOx8 -SLOT 2 FXOx8 -SLOT 3 FXSx8 -SLOT 4 FXSx8 -SLOT 5 FXSx8 -SLOT 6 FXSx8 -NOTES: -1. It is necessary to issue the commands 'restore defaults' - and 'reset' BEFORE downloading the configuration file to - ensure proper configuration. -2. Lines beginning with '-' will be ignored as comments - by the CLI. Before downloading, review the sections of - the configuration file delimited by these comments and - delete the commands that are not needed (e.g. 'set ip - address' and 'add user' are likely candidates for - deletion). -3. While downloading, a character delay of 5 ms and a line - delay of 300 ms is recommended. ------------------------------------------------------------- -Turning off verification messages. set verification off -Setting local off. set local off -Disconnecting all connections. disconnect a disconnect 1 disconnect 2 disconnect 3 disconnect 4 disconnect 5 disconnect 6 -Setting IP addresses. set ethernet ip address 10.10.1.100 255.255.0.0 set ip gateway 10.10.1.1 -Setting the SNMP MIB-II System Group objects. set snmp getcom "public" set snmp setcom "public" set snmp trapcom "public" set snmp trapauth enable set snmp trapevent all set snmp trapvers 2 -Setting slot a. set a:1 up set a:1 fdl none set a:1 lbo 1 set a:1 framing esf set a:1 id "CAC DS1# A:1" set a:1 linecode b8zs set a:1 loopdetect on set a:1:1-24 side drop set a:1:1-24 type voice set a:1:1-24 signal ls set a:2 down set a:2 fdl none set a:2 lbo 1 set a:2 framing esf set a:2 id "CAC DS1# A:2" set a:2 linecode b8zs set a:2 loopdetect on set a:2:1-24 side drop set a:2:1-24 type voice set a:2:1-24 signal ls -Setting slot 1. set 1:1-8 signal lscpd set 1:1-8 txgain -3 set 1:1-8 rxgain -3 -Setting slot 2. set 2:1-8 signal ls set 2:1-8 txgain -3 set 2:1-8 rxgain -6 -Setting slot 3. set 3:1-8 signal ls set 3:1-8 txgain -3 set 3:1-8 rxgain -6 set 3:1-8 linelength short -Setting slot 4. set 4:1-8 signal ls set 4:1-8 txgain -3 set 4:1-8 rxgain -6 set 4:1-8 linelength short -Setting slot 5. set 5:1-8 signal ls set 5:1-8 txgain -3 set 5:1-8 rxgain -6 set 5:1-8 linelength short -Setting slot 6. set 6:1-8 signal ls set 6:1-8 txgain -3 set 6:1-8 rxgain -6 set 6:1-8 linelength short -Setting primary and secondary clock sources. set clock1 internal set clock2 internal -Making connections. connect a:1:1 2:1 connect a:1:17-24 3:1-8 connect a:2:1-8 4:1-8 connect a:2:9-16 5:1-8 connect a:2:17-24 6:1-8 -Turning verification on. set verification on _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
