On Mon, Feb 01, 2010 at 07:42:51AM +0000, frangky robert wrote: > > > > > I do some test: > 1.unplug usb connector from server to astricon > 2.unplug power to astricon > 3.plug-in the power to astricon > 4.plug-in the usb connector > > Here is the log from /var/log/messages after doing the 1st step. > > Feb 1 19:38:24 localhost last message repeated 2 times > Feb 1 19:43:39 localhost kernel: ERR-xpp_usb: xusb-0 (usb-0000:00:1d.7-3) > [X1038295]: nonzero write bulk status received: -71 (pending_writes=1) > Feb 1 19:43:39 localhost kernel: usb 2-3: USB disconnect, address 3 > Feb 1 19:43:39 localhost kernel: ERR-xpp_usb: XBUS-00: xusb_listen: > usb_submit_urb failed: -19 > Feb 1 19:43:39 localhost kernel: INFO-xpp: XBUS-00: [usb:X1038295] > Disconnecting > Feb 1 19:43:39 localhost kernel: INFO-xpp: XBUS-00: [usb:X1038295] > Deactivating > Feb 1 19:43:39 localhost kernel: INFO-xpp: XBUS-00: [usb:X1038295] Release > XPDS > Feb 1 19:43:39 localhost kernel: INFO-xpp: XBUS-00/XPD-00: Remove > Feb 1 19:43:39 localhost kernel: INFO-xpp: XBUS-00/XPD-10: Remove > Feb 1 19:43:39 localhost kernel: INFO-xpp: XBUS-00/XPD-20: Remove > Feb 1 19:43:39 localhost kernel: NOTICE-xpp: worker_reset: > worker(XBUS-00)->xpds_init_done=0 > Feb 1 19:43:39 localhost kernel: INFO-xpp: XBUS-00: [usb:X1038295] Atribank > Remove > Feb 1 19:43:39 localhost kernel: INFO-xpp: XBUS-00: [usb:X1038295] Astribank > Release > Feb 1 19:43:39 localhost kernel: INFO-xpp_usb: xusb-0 (usb-0000:00:1d.7-3) > [X1038295]: now disconnected > Feb 1 19:43:39 localhost 'astribank_hook'[3728]: offline(XBUS-00): 0/1 from > /etc/dahdi/xpp_order > Feb 1 19:43:39 localhost 'astribank_hook'[3735]: All Astribanks offline > > > And, this is the log after doing 4th step. > > Feb 1 19:44:20 localhost kernel: usb 2-3: new high speed USB device using > ehci_hcd and address 4 > Feb 1 19:44:20 localhost kernel: usb 2-3: configuration #1 chosen from 1 > choice > Feb 1 19:44:21 localhost 'xpp_fxloader'[3847]: Exiting... > XPP_HOTPLUG_DISABLED
Seems like you explicitly disabled firmware loading by setting XPP_HOTPLUG_DISABLED in /etc/dahdi/init.conf . Just rem-out that line. > > lsusb result is: > > [r...@localhost ~]# lsusb > Bus 002 Device 004: ID e4e4:1160 > Bus 002 Device 001: ID 0000:0000 > Bus 006 Device 001: ID 0000:0000 > Bus 006 Device 002: ID 04b3:3025 IBM Corp. > Bus 004 Device 001: ID 0000:0000 > Bus 008 Device 001: ID 0000:0000 > Bus 007 Device 001: ID 0000:0000 > Bus 001 Device 001: ID 0000:0000 > Bus 005 Device 001: ID 0000:0000 > Bus 003 Device 001: ID 0000:0000 > > here is the msg when i do /usr/share/dahdi/xpp_fxloader > [r...@localhost ~]# /usr/share/dahdi/xpp_fxloader usb This only runs USB firmware loading. And as the firmware loading is explicitly disabled on your system, the FPGA firmware will still not get loaded. This is also something that you would have seen if you would run 'dahdi_hardware -v' So basically just remove that line from init.conf and replug the Astribank. -- Tzafrir Cohen icq#16849755 jabber:tzafrir.co...@xorcom.com +972-50-7952406 mailto:tzafrir.co...@xorcom.com http://www.xorcom.com iax:gu...@local.xorcom.com/tzafrir -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users