Hi I sugest you to make a reset and switch off the phone before upgrade.
It solved many problems for me. Miklos ----- Original Message ----- From: "Rich Adamson" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, January 23, 2004 11:32 AM Subject: Re: [Asterisk-Users] Snom 200 phones not working. > Ariel, > > > I have 2 Snom 200 and would like to get them to work properly with > > Asterisk. With the Firmware 2.02t I am able to use the phone. But only > > one line configured. With there newer firmware 2.03o it will not allow > > me to make calls. But I can get calls on the unit. Again the 2nd line > > is not able to be registered. Is this an issue with Asterisk or Snom? > > > > I could use some example configuration files. I have followed the Snom > > FAQ step by step. But it's still not working. > > I just upgraded my 200 to v2.03o and its working fine with two extns > defined. I happen to be using * CVS-12/04/03-14:24:40 on the same wire > (no nat, etc). > > My sip.conf entries look like: > [3007] > type=friend > host=dynamic > username=3007 > secret=mypassword > context=from-sip > > [3008] > type=friend > host=dynamic > username=3008 > secret=mypassword > context=from-sip > > Using your web browser to config the phone, verify: > Settings/SIP/Lines > Account = 3007 (to match above sip.conf def) > Registrar = ip address of asterisk box > Action = proxy > Account = 3008 (to match above sip.conf def) > Registrar = ip address of asterisk box > Action = proxy > Settings/SIP/Stack > Outbound Proxy, Registrar is outbound proxy = yes > Settings/SIP/Authentication > Line 1, Realm = asterisk, Username = 3007, Pasword = mypassword > Line 2, Realm = asterisk, Username = 3008, Pasword = mypassword > Settings/Key Mapping > P1 = Line, Number = 3007 > P2 = Line, Number = 3008 > > After ensuring your phone settings actually match the sip.conf settings > and that you've properly selected "Save" after changing each of the above > entries in the phone, then reboot the phone. If the phone prompts you to > download another firmware image, simply press ESC. (Seems some config > changes don't take effect until after a phone reboot.) > > The above config has been working fine with the last several (estimate > about 10) firmware versions, however the "user" interaction with several of > the keys are rather non-intuitive (or even backwards) for US users. > > For example, if you answer an incoming call on Line 1 (x3007 above) and place > that call on hold using the "Hold" key, then select Line 2 (x3008) to do a > consultive call to a different extn, you have to press the ESC key to hang > up that second consultive call. If instead of pressing the ESC key you > simply press Line 1 to return to the original call, Line 2 is automatically > put on hold (instead of dropping the line as it does in the US). If you're > not paying attention to the LEDs, you've now tied up the second line/extn > until such time as you muck around to release it. > > If that second (consultive) call happens to be to a pstn user and your > Central Office supports calling-party line supervision, you've probably > tied up that person's telephone line as well. (Email comments to snom > resulted in push-back, suggesting the ESC key is the proper way to drop > that second line. I'd guess US users (not techie's) will object to using > the phone in any form of production telephony.) > > I've not tried the 200 with the later CVS versions, so don't have a clue as > to what you're milage may be. > > Rich > > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
