I had already tried that, however my register statement already specifies to ring out on ext 1001 so the call isn't an unqualified one so should not look up the s extension
register => 2xxxx:[EMAIL PROTECTED]/1001 However I put the s extension statements in and the results were the same with or without the /1001 on the register statement. When I run the SIP DEBUG command from the console, I can see the CLI of the phone I am calling from in the sip statements however the asterisk box just sends out an engaged tone. A bit of background to the box, it is running a full install of Redhat 9 without the firewall enabled. (I did a full install as I thought it would be good to learn about Linux as well) It is not behind a NAT and configured with a static Public IP. Does anyone know of problems that can occur with a full install of Redhat 9? As I have read somewhere that someone recommends Redhat 8 and not 9 but he wasn't specific as to why, does anyone know of any problems (or is it a wild goose chase to read into it too much) If anyone else has any ideas I would be much appreciated. Elman Thankyou very much for taking the time out to respond. Would any of you suggest blatting the PC and starting again with a basic bare minimum config, i.e. no GUI Regards Stuart Buchanan ------------------------------------------------------------------------ This email is only for the intended recipient. If you have received this email in error please notify the sender, and delete the message immediately as it may contain privileged or confidential information This email has been checked for viruses to ensure that any attachments are free from viruses. You should, however carry out your own virus check before opening any attachment. We accept no liability for loss or damage caused by software viruses. ------------------------------------------------------------------------ -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Elman Efendiyev Sent: 24 July 2004 19:53 To: [EMAIL PROTECTED] Subject: RE: [Asterisk-Users] Please help I fear I have missed something very important! but what? Looks like you missed 's' extension for incoming calls You need something like this in extensions.conf exten => s,1,Answer exten => s,2,Dial(SIP/1001,20,t) See sample of extensions.conf in asterisk distribution (make samples if you didn't install samples) -- Sincerely, Elman Efendiyev [EMAIL PROTECTED] -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Sales Sent: Saturday, July 24, 2004 9:03 PM To: [EMAIL PROTECTED] Subject: [Asterisk-Users] Please help I fear I have missed something very important! but what? Sorry about this, I have been struggling with the basics of my asterisk config. I set up two sip peers and two phones. And I set up lots of dial masks for outgoing calls, all my outgoing calls were working great, however incoming calls were a different matter altogether, I cannot get incoming calls to work. So I have gone back to a very basic FWD config, with one phone which as far as I am aware should work, but doesn't. I cannot find info on how to fix this. Below is my sip.conf [general] port = 5060 bindaddr = xxx.xxx.xxx.xxx context = sip register => 2xxxx:[EMAIL PROTECTED]/1001 [fwd] type=friend secret=xxxxxx username=xxxxxx host=fwd.pulver.com ; ; [1001] type=friend username=xxxxxx host=dynamic secret=xxxxxxx callerid=Home <1001> dtmfmode=RFC2833 mailbox=1001 context=sip and here is my extensions.conf: [general] static=yes writeprotect=no ; [globals] HOME=SIP/1001 ; [sip] exten => 1001,2,Dial(SIP/1001,20,t) include => fwdnet ; [fwdnet] exten => _8.,1,Dial,SIP/${EXTEN:[EMAIL PROTECTED],t Now as I said I can call out no probs by dialing 8 then the FWD number, but incoming calls don't work, and as far as I can see that should ring ext 1001 for 20 secs. Could someone please help a complete Linux/Asterisk Newb, as apart from this I have learnt a hell of a lot. But it's the last thing I need to solve. The linux box for this testing has a unfirewalled public IP address, so there is no problems with NAT Please please can someone help. If I have missed something important then I aplogise, as I have been scouring the wiki and the archives to no avail Regards Stuart Buchanan ------------------------------------------------------------------------ ------ This email is only for the intended recipient. If you have received this email in error please notify the sender and delete the message immediately. This email has been checked for viruses to ensure that any attachments are free from viruses. You should, however, carry out your own virus check before opening any attachment. We accept no liability for loss or damage caused by software viruses. ------------------------------------------------------------------------ ------ _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
smime.p7s
Description: S/MIME cryptographic signature
