|
Hello !
I am a new user with Asterisk software. I managed to compile asterisk on my Redhat 9 box, and also to compile openh323 and pwlib software. I configured Asterisk to load the h323 module: [chan_h323.so] => (The NuFone Network's Open H.323 Channel Driver) == Parsing '/etc/asterisk/h323.conf': Found == Creating H.323 Endpoint == Registered channel type 'H323' (The NuFone Network's Open H.323 Channel Driver) == H.323 listener started == Parsing '/etc/asterisk/enum.conf': Found == Parsing '/etc/asterisk/logger.conf': Found Asterisk Event Logger restarted
When I start asterisk everything seems to be ok (no error messages), but I cannot see anything listening on 1720 port of the computer (for h323 protocol calls), nor on the 5060 port (for SIP calls).
Please help !
Thank you !
And this is the content of the /etc/asterisk/h323.conf file: [EMAIL PROTECTED] asterisk]# cat /etc/asterisk/h323.conf | more ; The NuFone Network's ; Open H.323 driver configuration ; [general] port = 1720 bindaddr = 81.18.80.117 ;tos=lowdelay ; ; You may specify a global default AMA flag for iaxtel calls. It must be ; one of 'default', 'omit', 'billing', or 'documentation'. These flags ; are used in the generation of call detail records. ; ;amaflags = default ; ; You may specify a default account for Call Detail Records in addition ; to specifying on a per-user basis ; ;accountcode=lss0101 ; ; You can fine tune codecs here using "allow" and "disallow" clauses ; with specific codecs. Use "all" to represent all formats. ; ;disallow=all allow=all ; turns on all installed codecs ;disallow=g723.1 ; Hm... Proprietary, don't use it... ;allow=gsm ; Always allow GSM, it's cool :) ; ; User-Input Mode (DTMF) ; ; valid entries are: rfc2833, inband ; default is rfc2833 ; dtmfmode=rfc2833 ; ; Set the gatekeeper ; DISCOVER - Find the Gk address using multicast ; DISABLE - Disable the use of a GK ; <IP address> or <Host name> - The acutal IP address or hostname of your GK ;gatekeeper = DISABLE ; ; ; Tell Asterisk whether or not to accept Gatekeeper ; routed calls or not. Normally this should always ; be set to yes, unless you want to have finer control ; over which users are allowed access to Asterisk. ; Default: YES ; ;AllowGKRouted = yes ; ; Default context gets used in siutations where you are using ; the GK routed model or no type=user was found. This gives you ; the ability to either play an invalid message or to simply not ; use user authentication at all. ; ;context=default ; ; H.323 Alias definitions ; ; Type 'h323' will register aliases to the endpoint ; and Gatekeeper, if there is one. ; ; Example: if someone calls [EMAIL PROTECTED] ; Asterisk will send the call to the extension 'time' ; in the context default ; ; [default] ; exten => time,1,Answer ; exten => time,2,Playback,current-time ; ; Keyword's 'prefix' and 'e164' are only make sense when ; used with a gatekeeper. You can specify either a prefix ; or E.164 this endpoint is responsible for terminating. ; ; Example: The H.323 alias 'det-gw' will tell the gatekeeper ; to route any call with the prefix 1248 to this alias. Keyword ; e164 is used when you want to specifiy a full telephone ; number. So a call to the number 18102341212 would be ; routed to the H.323 alias 'time'. ; ;[time] ;type=h323 ;e164=18102341212 ;context=default ; ;[det-gw] ;type=h323 ;prefix=1248,1313 ;context=detroit ; ; ; Inbound H.323 calls from BillyBob would land in the incoming ; context with a maximum of 4 concurrent incoming calls ; ; ; Note: If keyword 'incominglimit' are omitted Asterisk will not ; enforce any maximum number of concurrent calls. ; ;[BillyBob] ;type=user ;host=192.168.1.1 ;context=incoming ;incominglimit=4
__________________________________________________________________
+ More ways to contact me
|
image001.gif
Description: Binary data
