I went through something similar recently though involving having a channel bank between myself and the world. The techniques used there should be applicable to simpler hardware.
To do this in a quantitative fashion you need a few different tools: - A recent patch to ztmonitor (or current CVS head) that adds an option to display a numerical representation, as well as the bar graph. See: http://bugs.digium.com/bug_view_page.php?bug_id=0002783 - A phone number for a 'type 102 milliwatt test line' at _your_ serving central office. Try calling the repair number for your telco - by assignment they're usually found in xxx-958-nnnn or xxx-959-nnnn ranges in North America. I don't recommend using a distant test line as there may be unknown influencing factors. - And optionally, another patch to chan_zap.c that allows the gains of a channel to be twiddled on the fly without reloading. See: http://bugs.digium.com/bug_view_page.php?bug_id=0002784 The steps I followed to set the rxgain were: 1. Edit /etc/asterisk/zapata.conf and ensure Tx and Rx gains are 0.0 across the board. I also recommend disabling the echo canceller and training during the tests. 2. Access the Channel Bank console and ensure hardware gains are 0.0 (or as close as possible) across the board - for simplicity I stick to adjusting within Asterisk. 3. Start 'ztmonitor' on the target trunk in 'quantitative' mode. 4. Dial the CO Milliwatt test line from inside Asterisk via the target trunk. Note the Rx level - it should be near 14844 5. If level is < optimal make the the rxgain for the channel more +ve. If > than optimal, more -ve. note - restart will be required to apply gains if not using cli patch. 6. Once optimal rxgain has been determined, set it in zapata.conf and restart asterisk. Now, to set the txgain you need to have at least two lines on the asterisk server so you can loop a call through the serving central office and back to your own milliwatt source - to be able to listen to the effect you have on your own outbound audio. 7. Modify the dialplan to have incoming calls on the target trunk go to a context that goes something like: exten => .....,1,Answer() exten => .....,2,Milliwatt() 8. This time start 'ztmonitor' but refer to the second trunk, not the trunk that terminates on Milliwatt(). 9. Dial the target trunk from inside Aaterisk via the second trunk. Note the Rx level - it should be near 14844 10. If level is < optimal make the the txgain for the target trunk more +ve. If > than optimal, more -ve. 11. Once optimal txgain has been determined, set it in zapata.conf and restart asterisk. Esentially, in the first step we're concerned with compensating for the line/interface loss by twiddling the Zap rxgain, thus: | CB | | Zap | | | | chan1 | |-------| |-------| Reference >-| TxTLP |>-Rx-->|Rxgain | Signal >-(loss)-/ | | | | <-> Internal data stream | RxTLP |<-Tx--<|Txgain | | | | | In the second step we're ensuring the interface has symmetric loss by following the path: | CB | | Zap | | | | chan1 | |-------| |-------| | TxTLP |>-Rx-->|Rxgain | -----<-(loss)-\ | | | | <-> Internal data stream / <-| RxTLP |<-Tx--<|Txgain | | | | | | Central Office | | | | chan2 | | |-------| |-------| \ >-| TxTLP |>-Rx-->|Rxgain | ->----(loss)--/ | | | | <-> Internal data stream compensated by | RxTLP |<-Tx--<|Txgain | chan2 rxgain | | | | We trust that once the call is inside or beyond the serving CO then it's all inside a digital domain and there is no loss. If you should end up on a call where the far end analog circuit has signficant loss then at least your amplitude will be comparable to everone elses. Hope that helps. Kris Boutilier Information Systems Coordinator Sunshine Coast Regional District > -----Original Message----- > From: Paul Dugas [mailto:[EMAIL PROTECTED] > Sent: November 5, 2004 10:41 AM > To: Asterisk Mailing List > Subject: [Asterisk-Users] Adjusting txgain/rxgain > {clip} > > Is seems to me (and to the digium support guy I've contacted) > that I need to adjust the tx and rx gains. The direction I've received > for doing so has been to "just fiddle with them till they sound better" > and I've done so without much success. I've read the wiki page about using > ztmonitor and adjusting till internal callers talking generates 50% > spikes on both Rx and Tx plots but doing so produces even more echo. > > What am I missing? Am I using ztmonitor correctly? Is there a more > step-by-step HOWTO for adjusting the gains? I feel I may > need a bit of hand-holding here. ;) > > Paul > {clip} _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
