Hi Adamson,
Thanks for such a comprehensive answers. Below is some more data for your feedback. I tried all, but it is still not working.
Any comments and advise based on below data?
0. The System is in Singapore.
1. I have an X100P Generic Clone Card bought over from eBay.
2. lspci output:
00:0e.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Intel Corp.: Unknown device 0003
Flags: bus master, medium devsel, latency 32, IRQ 12
I/O ports at ec00
Memory at ef001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
3. lsmod output:
Module Size Used by wcfxo 12448 0 zaptel 241028 1 wcfxo crc_ccitt 1985 1 zaptel
4. /usr/sbin/zaptel/zttool output: I see the output below:
Zaptel Tool (C)2002 Linux Support Services, Inc.
���������������������� Zapata Telephony Interfaces �����������������������
� �
� Alarms Span �
� OK Generic Clone Board 1 � �
� � �
������������������� Generic Clone Board 1 �������������������� � � � � � Current Alarms: No alarms. � � Sync Source: Internally clocked � � IRQ Misses: 0 � � Bipolar Viol: 0 �
� Tx/Rx Levels: 0/ 0 �
� Total/Conf/Act: 1/ 1/ 0 �Span 1: 1 total channels, 1 configured F1=Details F10=Quit
5. the show modules from asterisk CLI ... output below:
chan_zap.so Zapata Telephony w/PRI 0
6. Zapata config is pasted below:
[channels] relaxdtmf=yes callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes usecallerid=yes echocancel=yes echocancelwhenbridged=yes rxgain=0.0 txgain=0.0 immediate=yes context=bell signalling=fxs_ks callerid=asreceived channel => 1
thanks& regards
----Original Message Follows---- From: Rich Adamson <[EMAIL PROTECTED]>
Would you tell us what country this system is in?
The zap show channels should look something like:
phoenix*CLI> zap show channels
Chan Extension Context Language MusicOnHold
pseudo inbound-bus-x10 en default
1 inbound-bus en default
and the 'zap show channel 1' should fill your cli screen with relevent
data. So, yes you have a problem with the zap channel, but with the
data included in your posting there isn't enough info to point to an
exact cause.>From the linux command line, do a 'lspci' and look for something that says "Tiger Jet". If you don't see something related to the x100p, then your system isn't recognizing the x100p. (I'm assuming this _is_ a digium x100p and not one of the knockoffs.)
>From the linux command line, do a 'cat /proc/interrupts' and look for the x100p driver (wcfxo if memory serves correctly). Is it there?
Change directory to /usr/src/zaptel and do a './zttool' from the command line. Do you see the x100p listed?
>From the linux command line, do a 'lsmod'. Is the wcfxo and zaptel drivers listed? Does the zaptel entry have a [wcfxo] to the right side of the line?
>From an asterisk cli, do a 'show modules'. Do you see something like: chan_zap.so Zapata Telephony w/PRI
If you see acceptable entries for all of the above, then it would appear something is very wrong with your /etc/asterisk/zapata.conf file. Don't know what, but could be spaces inserted where there shouldn't be, control characters embedded that can't be seen, or whatever. Worst case, rename that file and create a new one ensuring all entries are entered correctly.
Rich
------------------------
> Hi Rich Adamson,
>
> Thanks for your valuable reply. The telco line is connected and working
> properly. The phone number is also correct (see the debug messages).
>
> 1. I suspected it may be SIP <-> SIP issue, which might be causing SIP to
> PSTN dialout problem.
>
> 2. Is there any command, which I can use to confirm the zap channels are
> okay?
>
> 3. Also this output from Asterisk CLI is weired, would you like to comment?
>
> > starwars*CLI> zap show channels
> > Chan Extension Context Language MusicOnHold
> > pseudo default default
> >
> > starwars*CLI> zap show channel 1
> > Unable to find given channel 1
>
> what should I get???
>
> thanks & regards
> Abdullah
>
>
> ----Original Message Follows----
> From: Rich Adamson <[EMAIL PROTECTED]>
>
> Looks like asterisk is trying to send the call out Zap/1, but is having
> an issue that appears almost like there is no telephone line attached to
> your x100p card. Is this machine located in the US and are you sure
> the pstn line is properly plugged to the card?
> Another remote possibility is that asterisk is detecting a busy signal
> on the pstn line. If you are in the US, what is 403142142? That isn't
> a standard US telephone number. (Nine digits?) Again, if this is in the
> US, best guess is that sending those digits out the pstn line is
> resulting in some sort of busy/congestion tone coming back from your
> telco.
>
> ------------------------
> > Hi Asterisk-ians!
> >
> > Need all of your help. I am stuck with this issue for last few days. I
> have
> > one X100P installed in my system. My Asterisk is registered with another
> > Asterisk Server/SIP provider as client and the call is successfully
> received
> > by my Asterisk server (named as starwars).
> >
> > Now, the extentions.conf file states, the incoming INTO * should go out
> to
> > fxo as below:
> >
> > exten => s,1,Dial(Zap/1/403142142)
> > exten => s,2,Dial(Zap/1/403132663)
> > exten => s,3,hangup
> >
> > whereas other file config is as below:
> >
> > zapata.conf
> > [channels]
> > relaxdtmf=yes
> > callwaiting=yes
> > callwaitingcallerid=yes
> > threewaycalling=yes
> > transfer=yes
> > cancallforward=yes
> > usecallerid=yes
> > echocancel=yes
> > echocancelwhenbridged=yes
> > rxgain=0.0
> > txgain=0.0
> > immediate=yes
> > context=bell
> > signalling=fxs_ks
> > callerid=asreceived
> > channel => 1
> >
> > zaptel
> >
> > fxsks=1
> > loadzone=us
> > defaultzone=us
> >
> > sip.conf
> > register => 7062210:9211:[EMAIL PROTECTED]
> >
> > [MyService]
> > type=peer
> > username=7062210
> > fromuser=7062210
> > secret=9211
> > host=192.168.7.16
> > context=incoming
> > fromdomain=sipdom.inf
> > nat=no
> > canreinvite=no
> > dtmfmode=inband
> >
> >
> > so whenever the call comes in from service provider's asterisk to my
> > starwars asterisk, I get the error messages captured below:
> >
> >
> > starwars*CLI> sip show registry
> > Host Username Refresh State
> > 192.168.7.16:5060 7062210 105 Registered
> > -- Executing Dial("SIP/192.168.7.14-085a4790", "Zap/1/67742142") in
> new
> > stack
> > Nov 30 01:41:52 NOTICE[507921]: app_dial.c:742 dial_exec: Unable to
> create
> > channel of type 'Zap'
> > == Everyone is busy/congested at this time
> > -- Executing Dial("SIP/192.168.7.14-085a4790", "Zap/1/61002663") in
> new
> > stack
> > Nov 30 01:41:52 NOTICE[507921]: app_dial.c:742 dial_exec: Unable to
> create
> > channel of type 'Zap'
> > == Everyone is busy/congested at this time
> > -- Executing Hangup("SIP/192.168.7.14-085a4790", "") in new stack
> > == Spawn extension (incoming, s, 3) exited non-zero on
> > 'SIP/192.168.7.14-085a4790'
> > -- Executing Dial("SIP/192.168.7.14-085a4790", "Zap/1/67742142") in
> new
> > stack
> > Nov 30 01:41:52 NOTICE[524305]: app_dial.c:742 dial_exec: Unable to
> create
> > channel of type 'Zap'
> > == Everyone is busy/congested at this time
> > -- Executing Dial("SIP/192.168.7.14-085a4790", "Zap/1/61002663") in
> new
> > stack
> > Nov 30 01:41:52 NOTICE[524305]: app_dial.c:742 dial_exec: Unable to
> create
> > channel of type 'Zap'
> > == Everyone is busy/congested at this time
> > -- Executing Hangup("SIP/192.168.7.14-085a4790", "") in new stack
> > == Spawn extension (incoming, s, 3) exited non-zero on
> > 'SIP/192.168.7.14-085a4790'
> >
> >
> > please note the output of the following commands:
> >
> > starwars*CLI> zap show channels
> > Chan Extension Context Language MusicOnHold
> > pseudo default default
> >
> > starwars*CLI> zap show channel 1
> > Unable to find given channel 1
> >
> > starwars*CLI> sip show registry
> > Host Username Refresh State
> > 192.168.7.16:5060 7062210 105 Registered
> >
> > starwars*CLI> sip show peers
> > Name/username Host Dyn Nat ACL Mask Port
> > Status
> > MyService/7062210 192.168.7.16 255.255.255.255 5060
> > Unmonitored
>
>
> _______________________________________________
> Asterisk-Users mailing list
> [EMAIL PROTECTED]
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
> _______________________________________________
> Asterisk-Users mailing list
> [EMAIL PROTECTED]
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
---------------End of Original Message-----------------
_______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
