Hunt group is set to "Standard Operation (default)" If you have 2 controllers presumably you have 2 ISDN2e lines. Have you asked BT to set up a hunt group so that the same number can be used to dial in to any of your 4 available channels ?
Best wishes, John --- Craig Waddington <[EMAIL PROTECTED]> wrote: > Thanks for the info, unfortunately that still > doesn't work for me. > > Making two outgoing using ISDN. > > Contr1: 2 B channels total, 0 B channels free. > Contr2: 2 B channels total, 2 B channels free. > *CLI> capi info > Contr1: 2 B channels total, 0 B channels free. > Contr2: 2 B channels total, 2 B channels free. > > If I try to dial incoming, I still get call failed > on my Mobile phone. > > When CAPI should push the call to the other card > which has two channels > free. > > What is your hunt group settings on your DIVA card? > > > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On > Behalf Of John Smith > Sent: 09 December 2004 10:39 > To: Asterisk Users Mailing List - Non-Commercial > Discussion > Subject: RE: [Asterisk-Users] CAPI, BRI and grouping > B channels > > Hi All, > > I have just this minute found a solution that works > for us. The problem is not with the asterisk > configuration but with the configuration of the > Eicon > Card. > > I use the Eicon-supplied http server on port 10005 > to > configure the Eicon card. On the hardware > configuration page, set: > > CAPI Call distribution = Standard behaviour > > After this change, I could have two simultaneous > channels open for calls initiated in either > direction. > > Notes on my setup: > > hardware > ======== > IBM PC 500Mhz Pentium III, 64MB ram > Digium X100P PCI card > Eicon Diva Server 2.0 PCI card > > software > ======== > RedHat 8.0 > Asterisk 1.0.1 > Eicon Linux driver package v 7.5 > Chan_capi-0.3.5 > > > Line > ==== > British Telecom ISDN2e line, configured > point-to-point, 6-digit presentation, and no ddi > numbers. > > > Best wishes, > > John. > > -------------------------------------------- > > > > > --- Craig Waddington <[EMAIL PROTECTED]> wrote: > > Hi, > > > > I have the exact same problem, we have two Eicon > > DIVA Cards (BRI UK), > > using chan_capi by Junghann. > > > > The cards have been tested and work perfectly, if > we > > make two outgoing > > calls simultaneously, and someone calls us, they > get > > a busy tone or call > > failed, yet capi info says 2 channels are still > > free??? > > > > My capi.conf says to use 2 controllers etc yet > > Chan_capi does not seem > > to work correctly. > > > > There is basically no information on the website > on > > how to configure for > > the above or no examples on how to use the capi > > features. > > > > We tried contact via email - no response. > > > > So decided to move over to using Cisco Routers and > > Bri modules, which > > actually works as it should. > > > > Using Callgroup doesn't make any difference: > > > > [interfaces] > > msn=123456789 > > incomingmsn=* > > controller=1,2 > > softdtmf=1 > > accountcode= > > context=incoming > > ;echosquelch=1 > > ;echocancel=yes > > ;echotail=64 > > callgroup=1 > > ;deflect=12345678 > > devices=2 > > > > In sip.conf > > > > [**] > > type=friend > > username=** > > secret=20 > > canreinvite=no > > host=dynamic > > context=test > > callgroup=1 > > pickupgroup=1 > > > > Maybe that may help. > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] > On > > Behalf Of John Smith > > Sent: 08 December 2004 23:57 > > To: [EMAIL PROTECTED] > > Subject: [Asterisk-Users] CAPI, BRI and grouping B > > channels > > > > > > > > Dear All, > > > > I have a working asterisk installation in the UK > on > > BRI point-to-point. > > > > I am using Redhat8 with one Eicon Diva Server 2.0 > > card > > with chan_capi-0.3.5 and Asterisk 1.0.1. > > > > I have got to the stage where I can make and > receive > > calls over ISDN. > > > > My question: > > > > How do I group the 2 B channels so that when one > > channel is in use, the other channel is availble > to > > receive[make] an incoming[outgoing] call ? > > > > At present, when only one channel is used, any > > attempt > > to dial in from outside is met with a busy tone. > > > > I think the 'group' directive is what I am looking > > for, but I don't know if it can be used in > > /etc/asterisk/capi.conf or even if that is the > > correct > > file to place it? modem.conf ? extensions.conf ? > > > > Any help gratefully received, and thank you to all > > for > > this excellent software. > > > > John. > > > > > > > > > ___________________________________________________________ > > > > Win a castle for NYE with your mates and Yahoo! > > Messenger > === message truncated === ___________________________________________________________ Win a castle for NYE with your mates and Yahoo! Messenger http://uk.messenger.yahoo.com _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
