Hi, This is the motherboard: SM X6DAE-XG2 Dual XEON 800FSB EMT64 w/2-Ch SATA-R 0&1,SVGA,2xGb LAN Dual Intel® Xeon EM64T Support up to 3.60 GHz Intel® E7520 (Lindenhurst) Chipset 1(x8) PCI-Express on (x16) Slot, 3 x 64-bit 133MHz PCI-X, 2 x 64-bit 100MHz PCI-X Slots ATI RageXL 8MB Graphics
Actually it doesnt have 4 cpus as i mentioned in my earlier mail. It has 2 XEON cpus with hyper-threading technology. Anyone has seenexperienced any problems with this motherboard? -Sid --- Eric Bishop <[EMAIL PROTECTED]> wrote: > Is it a HP-Compaq DLXXX G4 machine? Because there is a thread here > about the TE410P not generating interrupts with these servers... > > > On Sat, 8 Jan 2005 05:14:39 -0800 (PST), Sid <[EMAIL PROTECTED]> wrote: > > Hi Scott, and Jack, > > > > --- Scott Stingel <[EMAIL PROTECTED]> wrote: > > > > > Sid- > > > > > > Try connecting one port to another. Note that one of the ports must be > > > set up as "cpe" and the other as "net" in zapata.conf when you loop them > > > together like this. > > > > > > A suitable crossover cable for testing can be constructed by cutting up > > > a CAT 5 cable, and connecting: > > > Pin 1 <--> Pin 4 on the other end > > > Pin 2 <--> Pin 5 > > > Pin 4 <--> Pin 1 > > > Pin 5 <--> Pin 2 > > > > > > You should get green's on both the connected channels if your zaptel and > > > zapata configurations are ok, and if you've run both modprobe and ztcfg > > > as documented. > > > > > > > Thanks for the valuable responses. We can only do the tests on monday, as > > the machine > is > > in a data center. Other than that we have done every tests we can think of > > and found > in > > the mailing list/wiki. The tests done at the NOC says that T1 is ok at > > their end. > Please > > see the following information about the system: > > > > The machine has 4 Xeon 2.80GHz CPUs. > > > > This is from /proc/interrupts > > 16: 0 0 0 3 IO-APIC-level usb-uhci > > 19: 0 0 0 0 IO-APIC-level usb-uhci > > 23: 0 0 0 0 IO-APIC-level ehci-hcd > > 26: 129024 0 0 28 IO-APIC-level eth1 > > 27: 0 0 21352 5 IO-APIC-level eth0 > > 76: 0 0 0 0 IO-APIC-level t4xxp > > > > # dmesg > > Zapata Telephony Interface Registered on major 196 > > Specify address with base=0xNNNNN > > Registered Tormenta2 PCI > > Found TE410P at base address fc8ff800, remapped to f8a40800 > > TE410P version c01a009b > > FALC version: 00000005, Board ID: 00 > > Reg 0: 0x371c9800 > > Reg 1: 0x371c9000 > > Reg 2: 0x07fc07fc > > Reg 3: 0x00000000 > > Reg 4: 0x00000000 > > Reg 5: 0x00000000 > > Reg 6: 0xc01a009b > > Reg 7: 0x00001000 > > Reg 8: 0x00000000 > > Reg 9: 0x00ff0000 > > Reg 10: 0x00000000 > > TE410P: Launching card: 0 > > TE410P: Setting up global serial parameters > > Found a Wildcard: Wildcard TE410P-Xilinx > > Registered tone zone 0 (United States / North America) > > TE410P: Span 1 configured for ESF/B8ZS > > SPAN 1: Primary Sync Source > > > > I am doubtful about the interrupts. Are those values ok? We have been after > > this > problem > > for more than a week now, we have tested with 2 different cards to no > > success. > > > > I'll post the results of the crossover connection test, once we do that. > > Thanks again > for > > the responses. > > > > BR, > > -Sid __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users