May I ask what you did? robert -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Vikram Rangnekar Sent: Tuesday, February 15, 2005 1:59 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Re: Sangoma A102 cards testing FIXED
Its fixed and working great. > > I was working on the dma issue that nenad pointed out and when i tried > to hdparm -d 1 /dev/hda my harddisk i got a permissioned denied error > (I was root) So i started researching a bit more and realised that > since i have a sata hdd and running it in IDE mode i cant start dma so > i just recompiled the kernel with sata drivers and scsi activated then > i change the bio SATA setting to SATA ENHANCED (nothing else seems to > work) and changed the root=/dev/hda2 to > root=/dev/sda2 in the kernel boot options and i was on my way. now > when i tierd hdparm -d 1 /dev/sda i was told that scsi dosent have dma > so it didnt matter. > > Next i started the wanpipe drivers and started asterisk i didnt get > any errors so to test th config i used > > exten => 111,1,Dial(Zap/g1/301) > exten => 111,2,Hangup > > and dialed that extension 111 and the extension 301 rang. i had > started pri intense debugging and used show channels to make sure the > call went over the e1 channels. > > i'm still testing it, it seems to be working great right now only > error i got was a FCS BAD or somthing like that once. > > My motherboard is a SuperMicro P4SCI just for your information. +++ Vikram Rangnekar [13/02/05 13:01 +0100]: > > Does anyone have any experience ith configureing the sangoma A102 card > for testing using a e1 cross cable i've configured and installed the > cards properly even the lights on the card are green which proves that > my cross cable is properly built too. my problem is with asterisk > which gives me these errors > > PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got > event: HDLC Bad FCS (8) on Primary D-channel of span 2 No D-channels > available! Using Primary on channel anyways 47! > PRI: !! Not good - head of queue has not been transmitted yet > > > I've tried everything i can think off with the wancfg configuration > files here is my zaptel and zapata configs. > > span=1,0,0,ccs,hdb3 > bchan=1-15 > dchan=16 > bchan=17-31 > > span=2,1,0,ccs,hdb3 > bchan=32-46 > dchan=47 > bchan=48-62 > > -------------------------- > zapata.conf > > switchtype=euroisdn > signalling=pri_net > group=1 > channel=>1-15 > channel=>17-31 > > group=2 > signalling=pri_cpe > channel=>32-46 > channel=>48-62 > ------------------------------- > do i need to fool around with some jumpers on the card or something to > activate internal clock on the card. zttol says INTERNALLY CLOCKED for > both the ports. There are NO Alarms and no missed IRQ's I'm using > asterisk 1.0.5 on debian with 2.4.29 kernel > > -- > regards > Vikram (http://www.vicramresearch.com) > _______________________________________________ > Asterisk-Users mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users -- regards Vikram (http://www.vicramresearch.com) _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
