a modprope zaptel loads fine. when i then do modprobe wcte11xp
i get the following:
/lib/modules/2.4.21-27.0.1.EL/misc/wcte11xp.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.21-27.0.1.EL/misc/wcte11xp.o: insmod /lib/modules/2.4.21-27.0.1.EL/misc/wcte11xp.o failed
/lib/modules/2.4.21-27.0.1.EL/misc/wcte11xp.o: insmod wcte11xp failed
I then went to
# cat /proc/interrupts
CPU0
0: 5200010 XT-PIC timer
1: 3 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 50373 XT-PIC ide0
8: 1 XT-PIC rtc
10: 661881 XT-PIC usb-ohci, eth0
14: 0 XT-PIC ide2
NMI: 0
ERR: 0and i don't see my wildcard, but...
#dmesg [snip] Zapata Telephony Interface Registered on major 196 Specify address with base=0xNNNNN Registered Tormenta2 PCI usb.c: registered new driver wcusb Wildcard USB FXS Interface driver registered [snip]
(should that be usb fxs??) and then a
# lspci -bv [snip]
00:05.0 System peripheral: Compaq Computer Corporation Advanced System Management Controller
Subsystem: Compaq Computer Corporation: Unknown device b0f3
Flags: medium devsel, IRQ 11
I/O ports at 1800
Memory at f5fe0000 (32-bit, non-prefetchable)
00:08.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 795e:0001
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at 2800
Memory at f5fd0000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
[snip]
shows my card is there, but sharing an IRQ with something else.
my zaptel.conf is
span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 loadzone=uk defaultzone=uk
and # ztcfg -v
Zaptel Configuration ======================
SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
31 channels configured.
ZT_SPANCONFIG failed on span 1: No such device or address (6)
which i guess makes sense...
Now, I'm a bit stuck as to the correct procedure for correcting this. Should I move the card to another slot, try going into the BIOS and allocating another IRQ no manually? is it even that that is causing the problem. (I haven't tried these yet as getting to the box is tricky, but if that will fix then i will obv make the trip)
Could anyone advise me how to proceed further on this? This is my first zaptel/PRI build after numerous SIP and CAPI configs without problems...
I'm hoping it is something simple, but i've never fiddled with IRQs before and just need someone to point me in the right direction.
Thanks in advance r
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
