Jon
----- Original Message ----- From: "Nenad Radosavljevic" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Friday, March 11, 2005 3:53 PM
Subject: [Asterisk-Users] Re: Incoming echo cancel
Same problem here: if call come over ISDN PRI and it is for a SIP phone that equals to strong echo situation, at the SIP end. Interestingly this doesn't happen on all calls but it does on 95% of them. Asterisk load at that moment is insignificant - 1 to 2 calls.
I have tried with all possible echo cancellers in zconfig.h, with and without MMX, and with and without CFLAGS+=-march=i686 in zaptel Makefile, but without any success.
TE110P is on its own interrupt - no other cards on board except Intel chipset PCI LAN card (on shared interrupt) and machine is Intel 685 chipset based, with P4 Celleron 2.6 GHz, 1Gbyte RAM, WD 10K RPM IDE HDD.
I have even contacted Digium support with this issue, but except a request for some additional explanations of my setup, nothing from them so far (for about a week).
Anyone have an idea, why this type of echo happens ? As far as I have read on the lists this type of echo should not occur at all, but it simply does !
Regards, Nenad Radosavljevic
Hi,
I'm having the same problems in echo cancellations that are mentioning in this mail of the list http://lists.digium.com/pipermail/asterisk-users/2003-July/016073.html , but I haven't found some reply to this mail.
I haven't echo problem on outcoming calls but echo cancellation is disabled in zaptel channels in incoming calls. Status of zaptel channel is the next:
localhost*CLI> zap show channel 32 Channel: 32LI> File Descriptor: 49 Span: 2 Extension: 958238500 Dialing: no Context: incoming Caller ID string: 685975350 Destroy: 0 InAlarm: 0 Signalling Type: PRI Signalling Owner: Zap/32-1 Real: Zap/32-1 Callwait: <None> Threeway: <None> Confno: -1 Propagated Conference: -1 Real in conference: 0 DSP: yes Relax DTMF: no Dialing/CallwaitCAS: 0/0 Default law: alaw Fax Handled: no Pulse phone: no Echo Cancellation: 256 taps, currently OFF PRI Flags: Call PRI Logical Span: Implicit Actual Confinfo: Num/0, Mode/0x0000 Actual Confmute: No Actual Hookstate: Onhook
I don't know because Asterisk doesn't enable echo cancelation.
Roberto Vargas.
------------------------------
Message: 11 Date: Fri, 11 Mar 2005 13:56:26 +0200 From: Herman Cremer <[EMAIL PROTECTED]> Subject: Re: [Asterisk-Users] how do i get rid of this blasted echo !!! To: Asterisk Users Mailing List - Non-Commercial Discussion <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain
Thanks Error.
I have switched to IAX looong ago....much better ! Just battle when doing double NAT :)
I dont have the phones here with me, but lets say its different...is there away to adjust the channel to fix the err ?
-herman
On Fri, 2005-03-11 at 13:24, [EMAIL PROTECTED] wrote:Hi Herman,
Look at the bottom of your phones and compare the REN values of both. Do they both value of REN 1.0? I think the one with the problem might have an REN value other than one. You tell me!
Errol Samuels "Don't let SIP Drive you crazy, use IAX2"
> On the echo... > > I have 2 extensions, with different analog phones. > The one works fine, the other echos and scratches > like mad !! > > I have switched the ports, cables etc but its ALWAYS > the same phone... > > Maybe this could be it ? > > Is it ok from a SIP phone ? > > Herman cremer > > > > > > _______________________________________________ > Asterisk-Users mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
------------------------------
Message: 12 Date: Fri, 11 Mar 2005 13:01:05 +0000 From: Niksa Baldun <[EMAIL PROTECTED]> Subject: Re: [Asterisk-Users] Unable to create Zap channel when dialing using a bri cellular gateway To: Asterisk Users Mailing List - Non-Commercial Discussion <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=ISO-8859-1
Obviously, your ISDN gateway is misconfigured somehow. I would suggest that you configure the gateway to dial some extension on your * box and see if incoming calls work. If they don't, then there is a problem with configuration of gateway's ISDN interface. If incoming calls work, then it is possible that the gateway is rejecting outgoing calls based on number called (I had that problem once), or perhaps you just forgot to pay the bill to your mobile operator :)).
Niksa
David Masure wrote:
Hi all,
I have an asterisk box set up with a bri card (using zaphfc). I have a bri cellular gateway connected to it beacuse I'd like to route all my cellular calls through that gateway.
The probel I encounter is that when trying to dial a phone number, I've the message : unable to create a zap channel.
My card is normally well configured because when connected to the NT, It works perfectly... The gateway is configured as a NT as well so no worry...
Has anyone an idea of what I should look for ?
Thank you
David Masure
------------------------------------------------------------------------
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
------------------------------
Message: 13 Date: Fri, 11 Mar 2005 19:58:37 +0800 From: Ronald Wiplinger <[EMAIL PROTECTED]> Subject: [Asterisk-Users] CDR database To: Asterisk Users Mailing List - Non-Commercial Discussion <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
I am looking at AMP and read "All the graphic & reports are based over the CDR database." How do I get the CDRs into a database?
bye
Ronald
------------------------------
Message: 14 Date: Fri, 11 Mar 2005 13:05:42 +0100 From: Marc Storck <[EMAIL PROTECTED]> Subject: [Asterisk-Users] SIP signalling and RTP to different servers To: Asterisk Users Mailing List - Non-Commercial Discussion <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
Hello,
we're in process of testing an interconnection with a trans-european carrier. But the carrier wants the SIP signalling to server 1 and the RTP stream to server 2. How do I configure asterisk to work with that type of installation. It seems they are using NexTone as SIP Signaling and RTP servers. Can someone help me???
Regards,
Marc -- CTO Marc Storck MS Networks SA [EMAIL PROTECTED] IT Service Provider http://www.msnetworks.lu 15, route d'Esch Phone: +352 2727 3030 L-4450 Belvaux Fax: +352 2727 3060
--------------- MS Networks powered service --------------- http://www.LuxAdmin.com Hosting and housing solutions -----------------------------------------------------------
------------------------------
Message: 15 Date: Fri, 11 Mar 2005 12:06:18 +0000 From: Robbie Hughes <[EMAIL PROTECTED]> Subject: RE: [Asterisk-Users] TE110P experiance To: [email protected] Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
- the PCI ID of the card seems to change over time which means that loading the module does not always recognise the card, only way to reset this is to power cycle the machine
I noticed this behaviour as well. i thought it was my motherboard wrongly assigning irq values - the symptoms i noticed were:
irq value set by me - machine starts, module loads, all functional reboot irq value reset to another /shared/ irq - machine starts, module fails reboot irq value set by me again - machine starts, module fails check irq - it has been reset to something else irq value set by me - machine starts, module loads, all functional
unfortunately my bios doesn't allow manual assigning of irqs - i have to swap them arond based on the ones it gives me... i ended up disabling my usb bus as i don't need it...
i can't find any consistency to it and am living in fear of the reboot.. very odd..
------------------------------
Message: 16 Date: Fri, 11 Mar 2005 09:09:00 -0300 From: Renato Mintz <[EMAIL PROTECTED]> Subject: [Asterisk-Users] SIP Phone Unreachable To: Asterisk Users Mailing List - Non-Commercial Discussion <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=US-ASCII
Hi Folks,
I found a strange problem trying to install a system on a customer. I have the following network configuration:
Asterisk - Router (NAT) - Internet - Router (NAT) - Grandstream Phone
The routers are low end D-Link router + broadband access. The router near asterisk has 5060 and 10000-10009 ports opened and assigned to Asterisk server. The router near the phone has default configuration: outgoing ok, incoming blocked.
I have Qualify = 1000. As soon as * is restarted I get a message telling the phone is unreachable. Looking at SIP debug I see * transmitting OPTIONS and receiving OK but it seems that * discards the OKs, because it always transmits OPTIONS 4 times (and receives 4 OKs), stop a little and begin transmitting OPTIONS again.
Looking at the SIP messages I found that the Call-ID in the OPTIONS message uses the Asterisk EXTERNAL IP address but the OK coming from the GS Phone has its Call-ID with the Asterisk INTERNAL IP address.
I run ethereal near the phone and the OK it sends has Asterisk EXTERNAL IP address! Somebody is translating the EXTERNAL IP into the INTERNAL IP at the Call-Id header.
I also run tcpdump at the Asterisk Server and the result is the same as the sip debug.
My simple conclusion is: the router is opening the SIP message and translating the Call-Id header IP, but I don't believe in that.
Any clue?
Thanks?
Renato
------------------------------
Message: 17 Date: Fri, 11 Mar 2005 14:11:12 +0200 From: Yair Hakak <[EMAIL PROTECTED]> Subject: Re: [Asterisk-Users] CDR database To: Asterisk Users Mailing List - Non-Commercial Discussion <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=US-ASCII
http://www.voip-info.org/wiki-Asterisk+billing
On Fri, 11 Mar 2005 19:58:37 +0800, Ronald Wiplinger <[EMAIL PROTECTED]> wrote:I am looking at AMP and read "All the graphic & reports are based over the CDR database." How do I get the CDRs into a database?
bye
Ronald
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
------------------------------
Message: 18 Date: Fri, 11 Mar 2005 12:15:35 -0000 From: "JunkMail" <[EMAIL PROTECTED]> Subject: Re: [Asterisk-Users] [EMAIL PROTECTED] silly problem, please help! To: "Asterisk Users Mailing List - Non-Commercial Discussion" <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset="iso-8859-1"
Solved!
The problem was that "capiinit start" can only be done by user "root" and
asterisk is started as user "asterisk".
Once I edited sudo ("visudo") and gave permission, the problem was solved.
Regards
M.G.
----- Original Message ----- From: "Junk Mail" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Wednesday, March 09, 2005 11:12 PM
Subject: [Asterisk-Users] [EMAIL PROTECTED] silly problem, please help!
notHi all!
After much struggling I got my [EMAIL PROTECTED] working fine AND making use of two AVMFritz!PCI cards. Really nice ! (kernel 2.4.2x)
There's however a silly glitch that's getting on my nerves, and, kind of a
newbie that I am to linux, it should be easy to get help :
-- "capiinit start" MUST BE run before Asterisk. (any other way makes *to start because chan_capi doesn't find CAPI support)
You must find this an easy thing, as I did. So I entered /etc/rc.d/ and inserted "capiinit start" to start as early as possible. Also added some lines of junk text so to see them going by as the system boots...
What's making me desperate is that the lines go by, capiinit is, in fact,
runned, and Asterisk still fails in the end.
I login and type my very first command "asterisk -vvvc" and it then starts
with no trouble.
Is this strange or what ?
Thanks in advance for your help.
M.G.
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
------------------------------
Message: 19 Date: Fri, 11 Mar 2005 15:12:36 +0200 From: Herman Cremer <[EMAIL PROTECTED]> Subject: [Asterisk-Users] IAX, double NAT To: Asterisk Users Mailing List - Non-Commercial Discussion <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain
has anyone managed to get IAX client (firefly 3rd party version) to work, where the *Server is behind single NAT, with port forwarding enabled on the NAT router, and the client behind double NAT ?
clients behind single nat to * work fine.
hermancremer
------------------------------
Message: 20 Date: Fri, 11 Mar 2005 05:12:02 -0800 (PST) From: <[EMAIL PROTECTED]> Subject: [Asterisk-Users] One single record file for a meetme monitor? To: [email protected] Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=us-ascii
I'm trying to figure out the best way to record a conference.
Many people suggest something like this: exten => 2060,1,Answer exten => 2060,2,Wait(1) exten => 2060,3,Monitor(wav,myfilename) exten => 2060,4,Meetme(1,ps)
However, this creates two files for each user that connects to the meetme. (I know they can be mux'd together to make one with sox..I've done that too) However, you still get 10 files if 10 users enter the meetme.
I'd really like to be able to simple record a single file with all the channels mux'd together.
Someone suggested executing a script and having the monitor application join the meetme. However, I have yet to see this work correctly.... and it isn't the best solution because I've got to have some logic to add the local listener when the first person enters... and exit when the last person exits.
Anyways, just wanted to see if any of you have this worked out already. I really think there should be an option on the meetme.
Thanks, Dave
------------------------------
Message: 21 Date: Fri, 11 Mar 2005 13:15:00 GMT From: Iqbal <[EMAIL PROTECTED]> Subject: Re: [Asterisk-Users] SetCallerID({$NEWCALLERID}) To: [email protected] Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=ISO-8859-1
that would do it, the $ is in the wrong place
Iqbal
On 3/11/2005, "beonice" <[EMAIL PROTECTED]> wrote:
--- Steven Frazier <[EMAIL PROTECTED]> wrote:I am trying to SetCallerID to a variable I have defined. This obviously is wrong. It actually sets the caller ID to $NEWCALLERID. I have search through the examples on wiki but wasn't able to find something similar to see what I was doing wrong. Could someone tell me the correct way to SetCallerID to a defined variable?
exten => 2125551212,5,SetCallerID({$NEWCALLERID})
--- snipped the rest ---
Off-hand, not having actually tested this, I'd guess that you have the $ in the wrong place. Move it one character to the left.
Cheers, Maya
__________________________________ Do you Yahoo!? Yahoo! Small Business - Try our new resources site! http://smallbusiness.yahoo.com/resources/ _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
------------------------------
Message: 22 Date: Fri, 11 Mar 2005 14:16:17 +0100 From: Giovanni Miano <[EMAIL PROTECTED]> Subject: [Asterisk-Users] [EMAIL PROTECTED] 0.6 + bristuff To: [email protected] Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain; charset=US-ASCII
How install bristuff in [EMAIL PROTECTED] ?
i tried version 0.2.Rca to last RC7k and when try to compile zaptel (after patched it) i've this error:
make: *** [zaptel.o] Error 1
------------------------------
Message: 23 Date: Fri, 11 Mar 2005 16:23:56 +0300 (EAT) From: "Julius Kidubuka" <[EMAIL PROTECTED]> Subject: [Asterisk-Users] Voicemail - No Audio Output! To: [email protected] Message-ID: <[EMAIL PROTECTED]> Content-Type: text/plain;charset=iso-8859-1
Hi all,
I am able to receive voicemail in my mail box but when I try to play the audio file attachment, I hear nothing at all (yet the caller on the other end does leave a voicemail message)!
Anyone had a similar problem before? Ideas are welcome!
Note: I am using [EMAIL PROTECTED] 0.6
Thanks in advance,
--
Rgds,
Julius Kidubuka.
"My advice to you is get married: if you find a good wife you'll be happy;
if not, you'll become a philosopher."
------------------------------
Message: 24 Date: Fri, 11 Mar 2005 14:25:45 +0100 (CET) From: Peter Svensson <[EMAIL PROTECTED]> Subject: RE: [Asterisk-Users] Panasonic TDA200 E1 -> E100P negotiation issues To: Asterisk Users Mailing List - Non-Commercial Discussion <[email protected]> Message-ID: <[EMAIL PROTECTED]> Content-Type: TEXT/PLAIN; charset=US-ASCII
On Fri, 11 Mar 2005, James Bean wrote:
Whooppss had pri_cpe set, redid the debug as attached.
They seem the same but just in case.
Asterisk does not see anything coming in on the D channel. What does zttool say about the state of the link?
As I said before, if the card is an isdn card you need to use ccs signalling. Cas signalling is unusual, but possible, over an E1. Can you find out the model number of the E1 card in the Panasonic pbx?
Peter
------------------------------
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users
End of Asterisk-Users Digest, Vol 8, Issue 89 *********************************************
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
