|
Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset,
and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of
zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it span=1,1,0,ccs,hdb3,crc4,yellow bchan=1-15,17-31 dchan=16 zapata.conf switchtype = EuroISDN signalling = pri_cpe pridialplan = unknown context = incoming group = 2 channel => 1-15,17-31 [EMAIL PROTECTED]:/usr/src# rmmod wct4xxp zaptel [EMAIL PROTECTED]:/usr/src# modprobe zaptel [EMAIL PROTECTED]:/usr/src# modprobe wct4xxp [EMAIL PROTECTED]:/usr/src# ztcfg -vv Zaptel Configuration ====================== SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0- Channel map: Channel 01: Individual Clear channel (Default)
(Slaves: 01) Channel 02: Individual Clear channel (Default)
(Slaves: 02) Channel 03: Individual Clear channel (Default)
(Slaves: 03) Channel 04: Individual Clear channel (Default)
(Slaves: 04) Channel 05: Individual Clear channel (Default)
(Slaves: 05) Channel 06: Individual Clear channel (Default)
(Slaves: 06) Channel 07: Individual Clear channel (Default)
(Slaves: 07) Channel 08: Individual Clear channel (Default)
(Slaves: 08) Channel 09: Individual Clear channel (Default)
(Slaves: 09) Channel 10: Individual Clear channel (Default)
(Slaves: 10) Channel 11: Individual Clear channel (Default)
(Slaves: 11) Channel 12: Individual Clear channel (Default)
(Slaves: 12) Channel 13: Individual Clear channel (Default)
(Slaves: 13) Channel 14: Individual Clear channel (Default) (Slaves:
14) Channel 15: Individual Clear channel (Default)
(Slaves: 15) Channel 16: D-channel (Default) (Slaves: 16) Channel 17: Individual Clear channel (Default) (Slaves: 17) Channel 18: Individual Clear channel (Default) (Slaves: 18) Channel 19: Individual Clear channel (Default) (Slaves: 19) Channel 20: Individual Clear channel (Default) (Slaves: 20) Channel 21: Individual Clear channel (Default) (Slaves: 21) Channel 22: Individual Clear channel (Default) (Slaves: 22) Channel 23: Individual Clear channel (Default) (Slaves: 23) Channel 24: Individual Clear channel (Default) (Slaves: 24) Channel 25: Individual Clear channel (Default) (Slaves: 25) Channel 26: Individual Clear channel (Default) (Slaves: 26) Channel 27: Individual Clear channel (Default) (Slaves: 27) Channel 28: Individual Clear channel (Default) (Slaves: 28) Channel 29: Individual Clear channel (Default)
(Slaves: 29) Channel 30: Individual Clear channel (Default)
(Slaves: 30) Channel 31: Individual Clear channel (Default)
(Slaves: 31) 31 channels configured. [EMAIL PROTECTED]:/usr/src# lsmod Module Size Used by Not tainted wct4xxp 51680 0 (unused) zaptel 175904 0 [wct4xxp] [EMAIL PROTECTED]:/usr/src# cat /proc/pci Bus 2, device 9, function 0: Communication controller: PCI device 10ee:0314
(Xilinx Corporation) (rev 1). IRQ 3. Master Capable. Latency=64. Non-prefetchable 32 bit memory at 0xf7eef800
[0xf7eef87f]. [EMAIL PROTECTED]:/usr/src# cat /proc/interrupts CPU0 0: 115864 XT-PIC timer 1: 141 XT-PIC keyboard 2: 0 XT-PIC cascade 3: 0 XT-PIC t4xxp 5: 2583 XT-PIC eth0 8: 1 XT-PIC rtc 10: 0 XT-PIC Intel ICH5 14: 2639 XT-PIC ide0 NMI: 0 ERR: 0 [EMAIL PROTECTED]:/usr/src# dmesg Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 02:09.0 Found TE410P at base address f7eef800, remapped to
e0978800 TE410P version c01a009b, burst ON FALC version: 00000005, Board ID: 00 Reg 0: 0x1eec6800 Reg 1: 0x1eec6000 Reg 2: 0x07fc07fc Reg 3: 0x00000000 Reg 4: 0x00000000 Reg 5: 0x00000000 Reg 6: 0xc01a009b Reg 7: 0x00001f00 Reg 8: 0x00000000 Reg 9: 0x00ff0000 Reg 10: 0x00000000 TE410P: Launching card: 0 TE410P: Setting up global serial parameters Found a Wildcard: Wildcard TE410P-Xilinx Registered tone zone 11 (Italy) TE410P: Span 1 configured for CCS/HDB3/CRC4 SPAN 1: Primary Sync Source TE410P: Span 1 configured for CCS/HDB3/CRC4 SPAN 1: Primary Sync Source Registered tone zone 11 (Italy) The jumpers are on E1, and the crossed cable should
be ok. Without loading the module the LED glows in red
colour, but the moment we load module, it goes off. (No red or green). We ran zttool and tried to run a loop test, but
zttool simply hung with the message 'Looping UP Span 1...'. We had to terminate
zttool with 'kill'. What's wrong ? Thanks, pixer |
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
